激光技术, 2016, 40 (2): 166, 网络出版: 2016-03-29  

NiCr-MoS2-M耐磨自润滑涂层的激光制备及表征

Laser preparation and characterization of NiCr -MoS2-M self-lubricating wear-resistant coating
作者单位
1 江苏大学 机械工程学院, 镇江 212013
2 东南大学 机械工程学院, 南京 211189
3 江苏联冠高新技术有限公司, 张家港 215600
摘要
为了提高挤出机螺杆表面的耐磨损性能, 采用激光熔覆技术在38CrMoAl钢表面制备NiCr-MoS2-M(M为CeO2-TiC-Cr3C2-V)耐磨自润滑复合涂层。通过X射线衍射仪(XRD)、扫描电子显微镜(SEM)及附带的能谱仪分析了涂层的物相组成及显微组织, 采用显微硬度计测试了涂层的显微硬度分布, 并在室温条件下测试了上述涂层的干滑动摩擦学性能, 取得了相关的数据。结果表明, XRD测试结果显示强化层主要由FeNi, Ni3Fe和Cr-Ni-Fe-C固溶体组成;用SEM观察发现强化层由固溶体枝晶、富Cr共晶和未熔MoS2颗粒组成。涂层中的显微硬度为313.7HV, 约为基体显微硬度(332.6HV)的94.32%; 摩擦系数为0.513, 约为基体摩擦系数(0.315)的1.63倍; 磨损量为58.561×10-3mm3, 约为基体磨损量(4.91×10-3mm3)的11.9倍。这一结果对进一步优化工艺参量, 以提高强化层的综合力学性能是有帮助的。
Abstract
To improve the wear resistance of extruder screws, self-lubricating wear-resistant NiCr-MoS2-M coating was fabricated on 38CrMoAl substrates by laser cladding. Phase composition and microstructures were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). Microhardness was measured with a microhardness tester. Tribological properties of the fabricated composite coatings were evaluated under dry sliding condition at room-temperature. The related data were obtained through theoretical analysis and experimental verification. XRD results show that the reinforced layer is composed of FeNi, Ni3Fe and Cr-Ni-Fe-C solid solution. According to SEM observation, the reinforced layer consists of solid solution dendrites, eutectic rich in Cr and undissolved MoS2 particles. The microhardness of the coating is about 313.7HV, about 94.32% of the matrix (332.6HV). Friction coefficient is about 0.513, about 1.63 times of the matrix (0.315). Wear loss of coatings is about 58.561×10-3mm3, about 11.9 times of the matrix (4.91×10-3mm3). This result is helpful for the further optimization of process parameters to improve the comprehensive mechanical properties of the reinforced layers.

童照鹏, 孙桂芳, 房晓玉, 黄学祥. NiCr-MoS2-M耐磨自润滑涂层的激光制备及表征[J]. 激光技术, 2016, 40(2): 166. TONG Zhaopeng, SUN Guifang, FANG Xiaoyu, HUANG Xuexiang. Laser preparation and characterization of NiCr -MoS2-M self-lubricating wear-resistant coating[J]. Laser Technology, 2016, 40(2): 166.

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!