首页 > 论文 > 应用激光 > 38卷 > 4期(pp:662-667)

激光光刀平面修正技术及实验研究

Correction Technology of Laser Light Knife Plane and Experimental Study

  • 摘要
  • 论文信息
  • 参考文献
  • 被引情况
  • PDF全文
分享:

摘要

针对传统线结构光光刀平面标定方法精度不高、标定过程复杂的问题, 在实验系统装调分析的基础上, 提出了线结构光光刀平面的修正方法。首先, 在线结构光旋转扫描测量原理的基础上, 设计了一种棋盘格与光刀平面重合的标定方案, 建立成像平面与光刀平面的映射关系; 然后, 根据实际装调过程中光刀平面与旋转轴的调整误差, 提出光刀平面与旋转轴夹角计算的实验方案, 确定出光刀平面与旋转轴的位置关系, 并获得夹角θ=1.146°; 最后, 以牙齿肩台预备体为测量对象, 对比分析了光刀平面与旋转轴夹角修正前后的三维形貌。实验结果表明, 牙齿肩台预备体旋转中心附近的凸起变形得到明显改善。

Abstract

Aiming at the problem that the calibration accuracy of the traditional linear structure light knife plane is not high and the calibration procedure is complex, based on installation and debugging of experimental system, a correction method of linear structure light knife light plane is proposed. Firstly, on the basis of rotation scanning measurement principle of linear structure light, the calibration method that checkerboard is coincident with the light knife plane is designed, and the mapping relation between the imaging plane and the light knife plane is established. Then, according to actual adjust error between light knife plane and rotation axis, the experimental scheme for calculating the angle between the light knife plane and rotation axis is proposed, and the position relationship between the light knife plane and the rotation axis is determined, the included angle θ=1.146°. Finally, the tooth shoulder is used as the measuring object, through the contrast and analysis of the three-dimensional profile before and after correction of the included angle between the light knife plane and the rotation axis. The experimental results show that the convex deformation near the rotation center of the tooth shoulder preparation is significantly improved.

Newport宣传-MKS新实验室计划
补充资料

中图分类号:TP302

基金项目:国家自然科学基金资助项目(项目编号: 61505157); 陕西省教育厅重点实验室资助项目(项目编号: 17JS048)

收稿日期:2018-04-25

修改稿日期:2018-05-24

网络出版日期:--

作者单位    点击查看

王小娟:西安工业大学理学院, 陕西 西安 710021
刘丙才:西安工业大学 陕西省薄膜技术与光学检测重点实验室, 陕西 西安 710021
鞠鑫:西安工业大学 陕西省薄膜技术与光学检测重点实验室, 陕西 西安 710021

联系人作者:王小娟(jellywxj@163.com)

备注:王小娟(1982-), 女, 实验员, 硕士, 主要从事光学三维轮廓测量方面的研究工作。E-mail:jellywxj@163.com

【1】LIN ZHIQIANG, WANG TIANYOU, NAN GANGLEI, et al.Three-dimensional data measurement of engine cylinder head blank based on line structured light[J].Opto-Electronic Engineering, 2014, 41(5): 46-51.
林志强, 王天友, 南刚雷, 等.基于线结构光的柴油机缸盖三维形貌测量[J].光电工程, 2014, 41(5): 46-51.

【2】HUANG FENGSHAN, CHEN LI, REN YOUZHI, et al.A vision weight method of billet based on linear structure laser[J].Opto-Electronic Engineering, 2015, 42(8): 27-33.
黄风山, 陈丽, 任有志, 等.连铸坯线结构光视觉定重方法[J].光电工程, 2015, 42(8): 27-33.

【3】LIU BAOLONG, SUN PING, CHEN HUA, et al.Research on 3D model reconstruction for cavity preparation based on laser triangulation[J].Journal of Xi′an Technological University, 2016, 36(1): 26-30.
刘宝龙, 孙萍, 陈桦, 等.义齿窝洞预备体三维重构关键技术研究[J].西安工业大学学报, 2016, 36(1): 26-30.

【4】XU YONGAN, YANG QIN, HUAI JINPENG.Calibration of the axis if the turntable in 4 axis laser measuring system and registration of multi view[J].Chinese Journal of Lasers, 2005, 32(5): 659-662.
徐永安, 杨钦, 怀进鹏.激光旋转扫描测量系统中转轴标定及多视拼合[J].中国激光, 2005, 32(5): 659-662.

【5】NIOAL V, ROSSI C, SAVINO S, et al.A method for the calibration of a 3-D laser scanner[J].Robotics and Computer-Integrated Manufacturing, 2011, 27(2): 479-484.

【6】ZHANG XU, ZHOU TAO.Center detection algorithm and knife plane calibration of flat top line structured light[J].Acta Photonica Sinica, 2017, 46(5): 51-59.
张旭, 周涛.平顶线结构光的中心检测算法及光刀平面标定[J].光子学报, 2017, 46(5): 51-59.

【7】HONG LEI, TIAN QILIANG, JI BAOJIAN.Calibration method for line structured-light parameters based on homography matrix[J].Acta Photonica Sinica, 2015, 44(12): 107-112.
洪磊, 田啟良, 嵇宝健.基于单应性矩阵的线结构光参量标定法[J].光子学报, 2015, 44(12): 107-112.

【8】CHEN TIANFEI, ZHAO JIBIN, WU XIANG.New calibration method for line structured light sensor based on planar target[J].Acta Optica Sinica, 2015, 35(1): 172-180.
陈天飞, 赵吉宾, 吴翔.基于共面靶标的线结构光传感器标定新方法[J].光学学报, 2015, 35(1): 172-180.

【9】LI GUANNAN, TAN QINGCHANG, KOU YING, et al.A new method for calibrating line structured-light 3D measurement model[J].Acta Photonica Sinica, 2013, 42(11): 1334-1339.
李冠楠, 谭庆昌, 寇莹, 等.一字线结构光三维测量模型的新型标定方法[J].光子学报, 2013, 42(11): 1334-1339.

【10】TRAN T T, HA C.Extrinsic calibration of a camera and structured multi-line light using a rectangle[J].International Journal of Precision Engineering & Manufacturing, 2018, 19(2): 195-202.

【11】WENDEL A, UNDERWOOD J.Extrinsic parameter calibration for line scanning cameras on ground vehicles with navigation systems using a calibration pattern[J].Sensors, 2017, 17(11): 2491.

【12】LAI HANXUAN, ZHANG ZHENGYU, ZHU LONG, et al.Nonlinear distortion correction of camera based on linear characteristic[J].Laser & Optoelectronics Progress, 2016, 53(2): 140-146.
赖瀚轩, 张征宇, 朱龙, 等.基于直线特征的摄像机非线性畸变自校正[J].激光与光电子学进展, 2016, 53(2): 140-146.

【13】HU MINGYONG, LI MINGJIE, ZHAO QI, et al.Design and imaging distortion correction of pin-hole objective lens with large field[J].Acta Optica Sinica, 2017, 37(5): 274-280.
胡明勇, 李明杰, 赵奇, 等.大视场针孔物镜设计及成像畸变校正[J].光学学报, 2017, 37(5): 274-280.

引用该论文

Wang Xiaojuan,Liu Bingcai,Ju Xin. Correction Technology of Laser Light Knife Plane and Experimental Study[J]. APPLIED LASER, 2018, 38(4): 662-667

王小娟,刘丙才,鞠鑫. 激光光刀平面修正技术及实验研究[J]. 应用激光, 2018, 38(4): 662-667

您的浏览器不支持PDF插件,请使用最新的(Chrome/Fire Fox等)浏览器.或者您还可以点击此处下载该论文PDF