应用激光, 2019, 39 (2): 285, 网络出版: 2019-06-10   

515 nm皮秒激光环切加工微孔实验研究

Experimental Study on 515 nm Picosecond LaserRing Cutting of Microholes
刘勇 1,2,3,*冯爱新 1,2,3贾天代 1,2,3陈欢 1,2,3
作者单位
1 温州大学机电工程学院,浙江 温州 325035
2 浙江省激光加工机器人重点实验室,浙江 温州 325035
3 温州大学激光与光电智能制造研究院,浙江 温州 325024
摘要
为解决毫/纳秒激光加工微孔质量差的问题,利用515 nm皮秒激光对厚度为0.1 mm的不锈钢进行环切法加工直径100 μm的微孔实验。采用激光共聚焦显微镜对加工后形貌和质量进行观察与表征,研究激光能量密度、扫描速度和离焦量等因素对加工后微孔形貌与质量的影响规律。实验结果表明,能量密度对微孔内壁质量有直接的影响,在保证去除能力前提下,控制能量密度在6.45 J/cm2以下,可有效减小微孔内壁的热影响区。同时实验还发现,适当增加扫描速度能够改善环切加工微孔切口和内壁的质量。在激光能量密度6.45 J/cm2、扫描速度200 mm/s时,孔锥度为2.72°。随着扫描速度的增大,锥度减小,最后稳定在2.29°左右,正离焦加工也能一定程度上减小孔的锥度。此研究结果表明,优化工艺参数能够加工出热影响区小、边缘质量好且锥度小的微孔。
Abstract
In order to solve the problem of poor microhole quality in millisecond/nanosecond laser processing, the 515 nm picosecond laser was used to ring cutting stainless steel with a thickness of 0.1 mm to process microholes with a diameter of 100 μm. Laser confocal microscopy was used to observe and characterize the morphology and quality of the processed microstructure. The effects of laser energy density, scanning speed and defocusing amount on the morphology and quality of microholes after processing were studied. The experimental results show that the energy density has a direct influence on the inner wall quality of the microholes. Controlling the energy density below 6.45 J/cm2 can effectively reduce the heat affected zone of the inner wall of the microholes under the premise of ensuring the removal ability. At the same time, it is found that appropriately increasing the scanning speed can improve the quality of the microhole incision and the inner wall of the ring cutting. When the laser energy density is 6.45 J/cm2 and the scanning speed is 200 mm/s, the hole taper is 2.72 degrees. As the scanning speed increases, the taper decreases, and finally stabilizes at about 2.29 degrees. The taper of the hole can also be reduced to some extent by the positive defocusing process. The results of this study show that the optimized process parameters can process microholes with small heat affected zone, good edge quality and small taper.

刘勇, 冯爱新, 贾天代, 陈欢. 515 nm皮秒激光环切加工微孔实验研究[J]. 应用激光, 2019, 39(2): 285. Liu Yong, Feng Aixin, Jia Tiandai, Chen Huan. Experimental Study on 515 nm Picosecond LaserRing Cutting of Microholes[J]. APPLIED LASER, 2019, 39(2): 285.

本文已被 5 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!