光学 精密工程, 2020, 28 (4): 885, 网络出版: 2020-07-02   

符合阿贝原则的数控机床几何误差建模

Geometric error model of CNC machine tools based on Abbe principle
作者单位
1 大连理工大学 机械工程学院, 辽宁 大连 116024
2 襄阳华中科技大学先进制造工程研究院, 湖北 襄阳 441053
摘要
为提高现有数控机床空间误差分析方法的准确度, 本文基于阿贝原则对齐次转换矩阵(HTM)几何误差补偿模型进行优化。首先, 推导出XYFZ型三轴机床适用的HTM几何误差补偿模型并给出模型正确使用的前提条件; 然后, 基于阿贝原则分析了三轴机床的空间误差传递机理, 指出阿贝误差对机床定位精度的影响, 给出理论计算公式并在机床运动轴上进行实验验证; 最后, 基于阿贝原则和布莱恩原则对现有的HTM几何误差补偿模型进行优化, 采用该模型拟合体对角线空间误差, 并与实测机床体对角线误差进行对比验证。现有HTM几何补偿模型可将机床空间误差由41.15 μm补偿至16.37 μm, 补偿率为60.22%; 优化后的补偿模型可将机床空间误差补偿至5.32 μm, 补偿率为87.07%, 提高了26.85%。实验结果表明, 优化后的补偿模型更加合理, 进一步改善了空间误差的补偿精度。
Abstract
In order to address the shortcomings of the existing space error analysis methods of CNC machine tools, the geometry error compensation model was optimized based on Abbe principle. First, the geometry error compensation model of the three-axis machine tool was deduced, and the precondition for the correct usage of the model was provided. Second, the mechanism of spatial error transfer of three-axis machine tool was analyzed, based on the Abbe principle. The influence of Abbe error on the positioning accuracy of machine tool was determined, and the theoretical calculation formula was provided and verified by conducting experiments on the moving axis of machine tool. Finally, the existing geometric error compensation model of HTM was optimized based on the Abbe principle and Bryan principle.This model was used to fit the diagonal space error, and compared with the actual measured diagonal error of the machine tool. The existing HTM geometric compensation model can compensate for the machine tool space error, altering it from 41.15 μm to 16.37 μm, with a compensation rate of 60.22%. The optimized compensation model can compensate for the machine tool space error, altering it to 5.32 μm, with a compensation rate of 87.07%, which is an increase of 26.85%. The experimental results show that the optimized compensation model is more reasonable, and further improves the accuracy of space error compensation.

赵壮, 娄志峰, 张忠宁, 王晓东, 范光照, 陈国华, 向华. 符合阿贝原则的数控机床几何误差建模[J]. 光学 精密工程, 2020, 28(4): 885. ZHAO Zhuang, LOU Zhi-feng, ZHANG Zhong-ning, WANG Xiao-dong, FAN Guang-zhao, CHEN Guo-hua, XIANG Hua. Geometric error model of CNC machine tools based on Abbe principle[J]. Optics and Precision Engineering, 2020, 28(4): 885.

本文已被 5 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!