强激光与粒子束, 2013, 25 (12): 3255, 网络出版: 2013-12-16   

点火黑腔用铝铜复合芯轴的制备及性能

Fabrication and performance of Al/Cu hybrid mandrel for NIF ignition hohlraum
作者单位
中国工程物理研究院 激光聚变研究中心, 四川 绵阳 621900
摘要
选取纯度较高的1100铝棒作为加工模芯的原材料,利用金刚石车床精加工出表面粗糙度均方根值小于20 nm的铝模芯,采用磁控溅射的方法在铝模芯上制备厚度大于5 μm的铜防护层,得到铝铜复合芯轴。对制备的铜防护层的表面微观结构、结晶性能、厚度一致性进行了分析测试,结果表明磁控溅射法制备的铜防护层沿(111)面择优生长,表面粗糙度均方根值小于30 nm,厚度一致性优于95%,圆柱度小于1 μm。镀层与基底结合力强,可满足大厚度黑腔涂层的制备需求。
Abstract
By comparing the chemical component and machined performance of two kinds of 1100 Al rod, the higher purity one is chosen for Al mandrel. Al mandrel is prepared by diamond turning machine with a surface roughness less than 20 nm (RMS) and Al/Cu hybrid mandrel is explored by depositing a 5 μm thick copper layer on Al mandrel via magnetron sputtering deposition. The surface roughness, thickness uniformity and crystallinity of Cu film are analyzed by white light interferometer, XRD. The results show that the prepared Cu film with surface roughness less than 30 nm (RMS), thickness uniformity more than 95%, and cylindricity less than 1 μm appears (111) preferential orientation growth. The interfacial bonding strength between Cu film and substrate is strong enough for depositing 11 μm thick hohlraum wall containing depleted uranium (DU).
参考文献

[1] 萨尔克夫Б Ю.惯性约束核聚变现状与能源前景[M].北京: 原子能出版社, 2008.(Шapкob Б Ю. Status and perspective of nuclear fusion energy with inertial confinement. Beijing: Atomic Energy Press, 2008)

[2] Wilkens H L, Nikroo A, Wall D R, et al. Developing depleted uranium and gold cocktail hohlraums for the National Ignition Facility[J]. Physics of Plasmas, 2007, 14: 056310.

[3] Dewald E L, Rosen M, Glenzer S H, et al. X-ray conversion efficiency of high-Z hohlraum wall materials for indirect drive ignition[J]. Physics of Plasmas, 2008, 15: 072706.

[4] Jones O, Schein J, Rosen M, et al. Proof of principle experiments that demonstrate utility of cocktail hohlraums for indirect drive ignition[J]. Physics of Plasmas, 2007, 14: 056311.

[5] 熊必涛,杨维才,罗文华,等.铀表面腐蚀初始阶段的理论模型[J].原子能科学技术, 2005, 39(s0): 146-150.(Xiong Bitao, Yang Weicai, Luo Wenhua, et al. Theoretical modeling of uranium surface corrosion at initial stage. Atomic Energy Science and Technology, 2005, 39(s0): 146-150)

[6] Cook R C, Kozioziemski B J, Nikroo A, et al. National Ignition Facility target design and fabrication[C]//3rd Moscow Workshop Targets & Applications. 2007.

[7] Foreman L R, Gobby P, Bamos J, et al. Hohlraum manufacture for inertial confinement fusion[C]//35th Annual Meeting of the American Nuclear Society. 1994.

[8] Haan S W, Salmonson J D, Clark D S, et al. NIF ignition target requirements, margins, and uncertainties: Status February 2010[C]//19th Target Fabrication Meeting. 2010.

[9] 杜凯,郑风成,谢军.机械研磨法制备晶体密度钼膜技术研究[J].强激光与粒子束, 2005, 17(6): 879-882.(Du Kai, Zheng Fengcheng, Xie Jun. Preparation of Mo films with theoretical density by lapping. High Power Laser and Particle Beams, 2005, 17(6): 879-882)

[10] Tsuji Y, Gasser S M, Kolawa E, et al. Texture of copper films Ta35 Si15N47 and Ti33Si23N44 underlayers[J]. Thin Solid Films, 1999, 350(1/2): 1-4.

[11] 陈瑞芳,高丽,花银群,等.磁控溅射工艺参数对Cu薄膜织构的影响[J].江苏大学学报: 自然科学版, 2009, 30(5): 483-486.(Chen Ruifang, Gao Li, Hua Yinqun, et al. Effect of sputtering parameters on texture of Cu films. Journal of Jiangsu University: Natural Science Edition, 2009, 30(5): 483-486)

[12] Messier R, Giri A P, Roy R A. Revised structure zone model for thin films physical structure[J]. J Vac Sci Techn A, 1984, 2(2): 500-506.

[13] 苏修梁,张欣宇.表面涂层与基体间的界面结合强度及其测定[J].电镀与环保, 2004, 24(2): 6-11.(Su Xiuliang, Zhang Xinyu. Interfacial bonding strength between surface coating and substrate and its measurement. Electroplating and Pollution Control, 2004, 24(2): 6-11)

赵利平, 邢丕峰, 杨蒙生, 郑凤成, 易泰民, 谢军, 袁光辉. 点火黑腔用铝铜复合芯轴的制备及性能[J]. 强激光与粒子束, 2013, 25(12): 3255. Zhao Liping, Xing Pifeng, Yang Mengsheng, Zheng Fengcheng, Yi Taimin, Xie Jun, Yuan Guanghui. Fabrication and performance of Al/Cu hybrid mandrel for NIF ignition hohlraum[J]. High Power Laser and Particle Beams, 2013, 25(12): 3255.

本文已被 1 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!