激光与光电子学进展, 2020, 57 (15): 152202, 网络出版: 2020-08-04   

数码裂隙灯显微系统前置物镜的设计 下载: 984次

Design of Front Objective for Digital Slit-Lamp Microscope System
作者单位
1 福建江夏学院电子信息科学学院先进传感技术实验室, 福建 福州 350108
2 福建师范大学光电与信息科学学院, 福建 福州 350007
摘要
数码裂隙灯显微镜主要用于眼科疾病的检查,而前置物镜作为数码裂隙灯显微镜的重要组成部分之一,影响整个系统的成像质量。根据体视显微镜平行光路系统的原理,利用Zemax软件设计并优化一款高性能数码裂隙灯显微镜前置物镜。实验结果表明:低倍光路和高倍光路的最大均方根半径值分别为2.3 μm和5.1 μm。在空间频率为115 lp/mm处,低倍光路时全视场的调制传递函数(MTF)值达到0.30,接近衍射极限,分辨率较高,高倍光路的MTF值在0.15以上,满足眼科使用要求。最后进一步分析偏心对系统引入的彗差和像散的影响,所得结果为加工和装调提供理论依据。
Abstract
Digital slit-lamp microscope is mainly used in the examination of ophthalmic diseases. The front objective lens is one of the important parts of the digital slit-lamp microscope, which affects the imaging quality of the entire system. Based on the parallel optical path principle of the stereo microscope, a high-performance front objective for a digital slit-lamp microscope is designed and optimized by using the Zemax software. Experimental results show that the maximum root mean squared radius of a spot diagram under low and high magnifications are 2.3 and 5.1 μm, respectively. At a spatial frequency of 115 lp/mm, the modulation transfer function (MTF) value of the full field of view under low magnification reaches 0.30, which is close to the diffraction limit and has a high resolution. Under high magnification, the MTF value is above 0.15, which meets the requirements of ophthalmology. Finally, further analysis the effect of eccentricity on the coma and astigmatism introduced by the system, providing a theoretical basis for machining and adjustment.

黄幼萍, 林峰, 黄淑燕, 陈冬英. 数码裂隙灯显微系统前置物镜的设计[J]. 激光与光电子学进展, 2020, 57(15): 152202. Youping Huang, Feng Lin, Shuyan Huang, Dongying Chen. Design of Front Objective for Digital Slit-Lamp Microscope System[J]. Laser & Optoelectronics Progress, 2020, 57(15): 152202.

本文已被 1 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!