[1] 石照耀, 姜海洋, 张敏. 产品几何规范中非理想表面的多尺度表征［J］. 光学 精密工程, 2016, 24(7): 1647-1654.

    SHI Z Y, JIANG H Y, ZHANG M. Multi-scale representation for skin models in geometrical product specifications ［J］. Opt. Precision Eng., 2016, 24(7): 1647-1654. (in Chinese)

[2] WHITEHOUSE D J. Handbook of surface and nanometrology ［M］. Boca Raton: CRC Press, 2010.

[3] LEACH R K. Fundamental principles of engineering nanometrology ［M］. Amsterdam: Elsevier/Willian Andrew, 2014.

[4] 李伯奎, 刘远伟. 表面粗糙度理论发展研究［J］. 工具技术, 2004, 38(1): 63-67.

    LI B K, LIU Y W. Study of developing tendency of surface roughness ［J］. Tool Engineering, 2004, 38(1): 63-67. (in Chinese)

[5] 陈继涛. 表面粗糙度检测方法发展史及研究现状概述［J］. 中国科技信息, 2007(17): 305-306.

    CHEN J T. A Survey of the research on surface roughness measuring development and method ［J］. China Science and Technology Information, 2007(17): 305-306. (in Chinese)

[6] 杨永成, 王运波. 表面粗糙度与光洁度等级对照［J］. 机械工程师, 1987(4): 44-45.

    YANG Y CH, WANG Y B. The comparison between surface roughness and the level of finish ［J］. Mechanical Engineer, 1987(4): 44-45. (in Chinese)

[7] 王玉田, 韩向春. 表面粗糙度的表征参数及其与表面功能特性的关系［J］. 燕山大学学报, 1983(4): 50-58.

    WANG Y T, HAN X CH. The relationship between characterization parameters of surface roughness and its functional properties ［J］. Journal of Yanshan University, 1983(4): 50-58. (in Chinese)

[8] 李成贵, 董申. 表面粗糙度的现状及发展［J］. 航空精密制造技术, 1999, 35(5): 1-4.

    LI C G, DONG S. The research status and development of surface roughness ［J］. Aviation Precision Manufacturing Technology,1999, 35(5): 1-4. (in Chinese)

[9] 刘长生, 张礼华. 机械零件表面粗糙度的影响与选择［J］. 现代制造工程, 2004(2): 114-115.

    LIU CH SH, ZHANG L H. Selection and effect of parts surface roughness ［J］. Modern Manufacturing Engineering, 2004(2): 114-115.(in Chinese)

[10] GRIEVE D J, KALISZER H and ROWE G W. A “Normal Wear” Process Examined by Measurements of Surface Topography ［J］. CIRP Annals, 1970, 16 (4): 585-592.

[11] 李成贵, 董申. 三维表面微观形貌的表征趋势［J］. 中国机械工程, 2000, 11(5): 488-492.

    LI CH G, DONG S. The Trends of characterizing 3D surface microtopography ［J］. China Mechanical Engineering, 2000, 11(5): 488-492. (in Chinese)

[12] ISO/FDIS 25178-2: 2010. Geometrical product specifications (GPS)-Surface texture: Areal-Part 2: Terms, definitions and surface texture parameters ［S］.

[13] STOUT K J. Development of methods for the characterisation of roughness in three dimensions ［M］. 1st Edition, Amsterdam: Elsevier, 1998.

[14] 张琳娜, 赵凤霞, 李晓沛,等. 现代产品几何技术规范(GPS)体系及应用分析［J］. 机械强度, 2004, 26(4): 400-404.

    ZHANG L N, ZHAO F X, LI X P, et al.. Analysis of modern product geometry specification (GPS) system and application ［J］. Journal of Mechanical Strength, 2004, 26(4): 400-404. (in Chinese)

[15] 李晓沛. ISO/TC213“产品的尺寸和几何规范及检验”工作近况［J］. 机械工业标准化与质量, 1996(12): 33-34.

    LI X P. Recent work of ISO/TC213 "product size and geometry specification and inspection" ［J］. Standardization and quality of machinery industry, 1996(12): 33-34.(in Chinese)

[16] WHITEHOUSE D J. The parameter rash-is there a cure ［J］. Wear, 1982, 83(1): 75-78.

[17] LEACH R K. Characterisation of Areal Surface Texture ［M］. Berlin Heidelberg: Springer, 2013.

[18] 陈国强, 张维强, 彭文静. 研磨表面微观形貌的三维检测及Areal表征［J］. 机械设计与研究, 2009, 25(2): 19-22.

    CHEN G Q, ZHANG W Q, PENG W J. Research on the 3-D detection and areal characterization of micro-topography of lapping surface ［J］. Machine Design and Research, 2009, 25(2): 19-22.(in Chinese)

[19] BLUNT L, JIANG X Q. Advanced Techniques for Assessment Surface Topography: Development of a Basis for 3D Surface Texture Standards SurfStand ［M］. Amsterdam: Elsevier, 2003.

[20] ISO. How to write standards ［R］. Geneva: International Organization for Standardization, 2013.

[21] GB/T 33523.6-2017. 产品几何技术规范(GPS)表面结构 区域法 第6部分: 表面结构测量方法的分类［S］.

    GB/T 33523.6-2017. Geometrical Product Specifications-surface texture: areal-part 6: Classification of surface structure measurement methods ［S］.(in Chinese)

[22] LEACH R K, DE GROOT P. The standards rash - is there a cure ［J］. International Journal of Metrology & Quality Engineering, 2015, 6(1): 101.

[23] JIANG X Q, SCOTT P J, WHITEHOUSE D J, et al.. Paradigm Shifts in Surface Metrology. Part II. The Current Shift ［J］. Proceedings Mathematical Physical & Engineering Sciences, 2007, 463(2085): 2071-2099.

[24] WHITEHOUSE D J. Surface and their measurement ［M］. London: Hermes Penton Ltd, 2002.

[25] 王永礼, 屠恒贤. 微观表面的表征技术与方法［J］. 安徽工业大学学报(自然科学版), 2005, 22 (4): 369-371.

    WANG Y L, TU H X. Characterization techniques and methods of micro-surface ［J］. Journal of Anhui University of Technology (Natural Science), 2005, 22 (4): 369-371.(in Chinese)

[26] 李成贵, 董申. 3D表面粗糙度的测量方法分析［J］. 航空精密制造技术, 1999, 32(02): 36-40.

    LI CH G, DONG SH. Methods and analysis of 3D surface roughness measurement ［J］. Aviation Precision Manufacturing Technology, 1999, 32(02): 36-40. (in Chinese)

[27] LEACH R K, HART A. A comparison of stylus and optical methods for measuring 2D surface texture ［R］. National Physical Laboratory (NPL) REPORT CBTLM 15, 2002.

[28] LEACH R K. Optical measurement of surface topography ［M］. Berlin: Springer-Verlag, 2011.

[29] VORBURGER T V, RHEE H G, RENEGAR T B, et al.. Comparison of optical and stylus methods for measurement of surface texture ［J］. International Journal of Advanced Manufacturing Technology, 2007, 33(1): 110-118.

[30] 陈建超, 冯世绪, 郭保苏,等. 表面微观形貌测量方法探讨［J］. 计量学报, 2016, 37(6A): 204-211.

    CHEN J CH, FENG SH X, GUO B S, et al.. Methods employed for measuring surface microtopography ［J］. Acta Metrologica Sinica, 2016, 37(6A): 204-211.(in Chinese)

[31] WHITEHOUSE D J. Comparison between stylus and optical methods for measuring surfaces ［J］. CIRP Annals, 1988, 37 (2): 649-653.

[32] 杨建虹. 表面粗糙度评定由二维向三维转化综述［J］. 机械工业标准化与质量, 2015, (505): 20-23.

    YANG J H. A summary of the transformation of surface roughness characterization from two-dimensional to three-dimensional ［J］. Machinery Industry Standardization & Quality, 2015, (505): 20-23.(in Chinese)

[33] 李惠芬, 蒋向前, 李柱. 三维表面功能评定技术发展综述［J］. 工具技术, 2002, 36(2): 8-11.

    LI H F, JIANG X Q, LI ZH. Summary of development of 3D surface function evaluation technology ［J］. Tool Engineering, 2002, 36(2): 8-11.

[34] MATHIA T G, PAWLUS P, WIECZOROWSKI M. Recent trends in surface metrology ［J］. Wear, 2011, 271(3): 494-508.

[35] STOUT K J, SULLIVAN P J,MCKEOWN P A. The use of 3D topographic analysis to determine the micro-geometric transfer characteristics of textured sheet surfaces through rolling ［J］. CIRP Annals, 1992, 41 (1): 621-624.

[36] WENNERBERG A, OHLSSONT R, ROSKNT B G, et al.. Characterizing three-dimensional topography of engineering and biomaterial surfaces by confocal laser scanning and stylus techniques ［J］. Medical Engineering Physics, 1996, 18(7): 548-556.

[37] DONG W P, STOUT K J. An integrated approach to the characterisation of surface wear: Qualitative characterisation ［J］. Wear, 1995, 181: 700-716.

[38] BLUNT L and EBDON S. The application of three-dimensional surface measurement techniques to characterizing grinding wheel topography ［J］. International Journal of Machine Tools and Manufacture, 1996, 36 (11): 1207-1226.

[39] XIE H C, CHEN D R, KONG X M. An analysis of the three-dimensional surface topography of textured cold-rolled steel sheets ［J］. Tribology International, 1999, 32(2): 83-87.

[40] JIANG X Q, BLUNT L, STOUT K J. Three-dimensional surface characterization for orthopaedic joint prostheses ［J］. Journal of Engineering in Medicine,1999, 213(1): 49-68.

[41] RAMASAWMY H, BLUNT L. 3D surface topography assessment of the effect of different electrolytes during electrochemical polishing of EDM surfaces ［J］. International Journal of Machine Tools and Manufacture, 2002, 42: 567-574.

[42] RAMASAWMY H, Blunt L and RAJURKAR K P. Investigation of the relationship between the white layer thickness and 3D surface texture parameters in the die sinking EDM process ［J］. Precision Engineering, 2005, 29(4): 479-490.

[43] BUTLER D L, BLUNT L, SEE B K, et al.. The characterisation of grinding wheels using 3D surface measurement techniques ［J］. Journal of Materials Processing Technology, 2002, 127(2): 234-237.

[44] AL-NAWAS B, GTZ H. Three-dimensional topographic and metrologic evaluation of dental implants by Confocal Laser Scanning Microscopy ［J］. Clinical Implant Dentistry and Related Research,2003, 5(3): 176-183.

[45] SUH A Y, POLYCARPOU A A, CONRY T F. Detailed surface roughness characterization of engineering surfaces undergoing tribological testing leading to scuffing ［J］. Wear, 2003, 255(1): 556-568.

[46] 王金明, 杨志翔. 复合材料切削表面粗糙度测试方法的研究［J］. 宇航材料工艺, 2004, 34(4): 59-62.

    WANG J M, YANG ZH X. Study of roughness measurement on cutting surface of composites ［J］. Aerospace Materials & Technology, 2004, 34(4): 59-62. (in Chinese)

[47] BNARD Q, FOIS M, GRISEL M. Influence of fibre reinforcement and peel ply surface treatment towards adhesion of composite surface ［J］. International Journal of Adhesion and Adhesives, 2005, 25(5): 404-409.

[48] KUNDRAK J, OSANNA P H, AFJEHI-SADA A, et al.. Surface quality of hard turned boreholes ［C］. Metrology for a Sustainable Development, XVIII IMEKO WORLD CONGRESS, Rio de Janeiro, Brazil: September 2006.

[49] KRZYZAK Z, PAWLUS P. 'Zero-wear' of piston skirt surface topography ［J］. Wear, 2006, 260(4): 554-561.

[50] SENIN N, ZILIOTTI M, GROPPETTI R. Three-dimensional surface topography segmentation through clustering ［J］. Wear, 2007,262(3): 395-410.

[51] 艾传智, 杨东军, 赵福令,等. C/C复合材料切削表面粗糙度的测量评定与影响因素研究［J］. 航空精密制造技术, 2005, 41(6): 31-34.

    AI CH ZH, YANG D J, ZHAO F L, et al.. Study on measurement & evaluation of cutting surface roughness of C/C Composite and the influential factors ［J］. Aviation Precision Manufacturing Technology, 2005, 41(6): 31-34.(in Chinese)

[52] 赵福令, 艾传智, 杨东军,等. 碳/碳复合材料切削表面粗糙度的评定方法及评定参数研究［J］. 计量学报, 2006, 27(3): 206-211.

    ZHAO F L, AI CH ZH, YANG D J, et al.. Study on the evaluation method and evaluation parameters of cutting surface roughness of carbon/carbon composite ［J］. Acta Metrologica Sinica, 2006, 27(3): 206-211.(in Chinese)

[53] BNARD Q, FOIS M and GRISEL M. Surface treatment of carbon/epoxy and glass/ epoxy composites with an excimer laser beam ［J］. International Journal of Adhesion and Adhesives, 2006, 26(7): 543-549.

[54] BROWN L T. The use of 3D surface analysis techniques to investigate the wear of matt surface finish femoral stems in total hip replacement ［D］. University of Huddersfield, 2006.

[55] SUL Y T, KANG B S, JOHANSSON C, et al.. The roles of surface chemistry and topography in the strength and rate of oseointegration of titanium implants in bone ［J］. Journal of Biomedical Materials Research, 2009, Part A, 89(4): 942-950.

[56] LE GUHENNEC L, SOUEIDAN A, LAYROLLE P, et al.. Surface treatments of titanium dental implants for rapid osseointegration ［J］. Dental materials. 2007, 23(7): 844-854.

[57] 袁成清, 严新平, 彭中笑. 磨粒的三维表面特征描述［J］. 摩擦学学报, 2007, 27(3): 294-296.

    YUAN CH Q, YAN X P, PENG ZH X. Three-dimensional surface characterisation of wear debris ［J］. Tribology, 2007, 27(3): 294-296. (in Chinese)

[58] VILA R F, GODOY C, ABRO A M, et al.. Topographic analysis of the crater wear on TiN, Ti (C, N) and (Ti, Al) N coated carbide tools ［J］. Wear, 2008, 265(1): 49-56.

[59] MICHALSKI J. Surface topography of the cylindrical gear tooth flanks after machining ［J］. International Journal of Advanced Manufacturing Technology, 2009, 43(5): 513-516.

[60] WAIKAR R A, GUO Y B. A comprehensive characterisation of 3D surface topography induced by hard turning versus grinding ［J］. Journal of Materials Processing Technology, 2008, 197(1): 189-199.

[61] NGUYEN A T, BUTLER D. Correlation of grinding wheel topography and grinding performance: A study from a viewpoint of three-dimensional surface characterisation ［J］. Journal of Materials Processing Technology, 2008, 208 (1): 14-23.

[62] ARIS N F M, CHENG K. Characterization of the surface functionality on precision machined engineering surfaces ［J］. International Journal of Advanced Manufacturing Technology, 2008, 38(3): 402-409.

[63] 李伯奎. 三维表面偏斜度与陡度的规律研究［J］. 计量技术, 2008(10): 3-6.

    LI B K. Study on the law of the skew and steepness of three-dimensional surface ［J］. Measurement Technique, 2008(10): 3-6.(in Chinese)

[64] SCARDINO A J, HUDLESTON D, PENG Z, et al.. Biomimetic characterisation of key surface parameters for the development of fouling resistant materials ［J］. Biofouling, 2009, 25 (1): 83-93.

[65] CZIFRA , HORVTH S. Complex microtopography analysis in sliding friction of steel-ferodo material pair ［J］. Meccanica, 2011, 46(3): 609-616.

[66] WANG J, JIANG X J, GURDAK E, et al.. Numerical characterisation of biomedical titanium surface texture using novel feature parameters ［J］. Wear, 2011, 271(7): 1059-1065.

[67] TIAN Y, WANG J, PENG Z, et al.. Numerical analysis of cartilage surfaces for osteoarthritis diagnosis using field and feature parameters ［J］. Wear, 2011, 271(9): 2370-2378.

[68] 墨洪磊, 朱永伟, 唐晓潇,等. 固结磨料研磨K9玻璃的工艺优化［J］. 金刚石与磨料磨具工程, 2012, 32(3): 7-11.

    MO H L, ZHU Y W, TANG X X, et al.. Parameter optimization when lapping K9 glass with fixed abrasive pad ［J］. Diamond & Abrasives Engineering, 2012, 32(3): 7-11. (in Chinese)

[69] 张丘, 刘维, 唐贤进. PBX炸药切削表面粗糙度评定及影响因素［J］. 含能材料, 2012, 20(6): 775-778.

    ZHANG Q, LIU W, TANG X J. Evaluation of Cutting Surface Roughness of PBX Explosive and Its Influentce Factors ［J］. Chinese Journal of Energetic Materials, 20(6): 775- 778. (in Chinese)

[70] 王晓强, 余真泷, 崔凤奎. 基于灰关联的三维表征参数与耐磨性相关性分析［J］. 河南理工大学学报(自然科学版), 2014, 33(6): 761-765.

    WANG X Q, YU ZH L, CUI F K. Correlation analysis of 3D characterization parameters and wear resistance based on grey correlation ［J］. Journal of Henan Polytechnic University (Natural Science), 2014, 33(6): 761-765. (in Chinese)

[71] BULAHA N. Analysis of service properties of cylindrically ground surfaces, using standard ISO 25178-2: 2012 surface texture parameters ［C］. Proceedings of the 10th International Scientific and Practical Conference, Rezekne, Latvia, 2015,1: 16-21.

[72] 刘泊, 齐兴华, 张明. 表面三维轮廓的粗糙度评定［J］. 光学 精密工程, 2016, 24(10s): 135-140.

    LIU B, QI X H, ZHANG M. Roughness evaluation of 3D surface profile ［J］. Opt. Precision Eng., 2016,24(10s): 135-140.(in Chinese)

[73] 徐善华, 何羽玲, 秦广冲,等. 钢材锈蚀率与表面三维粗糙度参数的关系［J］. 材料科学与工程学报, 2016, 34(2): 292-295.

    XU SH H, HE Y L, QIN G CH, et al.. Relationship between steel corrosion ratio and 3D surface roughness parameters ［J］. Journal of Materials Science and Engineering, 2016, 34(2): 292-295.(in Chinese)

[74] 杨洁, 李乐. 基于机器视觉的表面粗糙度测量与三维评定［J］. 光学技术, 2016, 42(6): 491-495.

    YANG J, LI L. Surface roughness measurement and three-dimensional assessment based on machine vision ［J］. Optical Technique, 2016, 42(6): 491-495.(in Chinese)

[75] 郑立功, 姚鹏, 张志宇,等. 金属结合剂金刚石砂轮的高压磨料水射流修锐技术［J］. 光学 精密工程, 2016, 24(10s): 477-483.

    ZHENG L G, YAO P, ZHANG ZH Y, et al.. High-pressure abrasive water jet dressing of metal bonded diamond grinding wheel ［J］. Opt. Precision Eng., 2016, 24 (10s): 477-483.(in Chinese)

[76] 谢俊峰, 何声馨, 李大磊,等. 表面状态对疲劳塑性变形局部化的影响［J］. 表面技术, 2017, 46(2): 224-228.

    XIE J F, HE SH X, LI D L, et al.. Effect of surface states on fatigue plastic deformation localization ［J］. Surface Technology, 2017, 46(2): 224-228.(in Chinese)

[77] GONG M, RAO SH ZH, LI L. Effects of machining parameters on surface roughness of joints in manufacturing structural finger-joined lumber ［J］. Journal of Forestry Engineering, 2017, 2(4): 10-18.

[78] LEACH R K, BROWN L, JIANG J, et al.. Measurement Good Practice Guide No. 108-Guide to the measurement of smooth surface topography using coherence scanning interferometry ［M］. National Physical Laboratory (NPL), 2008.

[79] 蒋向前, L. Blunt. 三维表面测量的发展［J］. 工程设计学报, 2000, 7(4): 98-100.

    JIANG X Q, BLUNT L. Advance in the Three-Dimensional Surface Metrology ［J］. Chinese Journal of Engineering Design, 2000,7(4): 98-100. (in Chinese)

[80] 李伯奎, 李年莲, 刘远伟,等. 表面粗糙度功能参数及其三维量值的实验研究［J］. 机械设计与制造, 2011,(9): 179-181.

    LI B K, LI N L, LIU Y W, et al.. Functional parameters of surface roughness and experimental study of its 3-D index ［J］. Machinery Design＆Manufacture, 2011, (9): 179-181. (in Chinese)

[81] 张洪玉, 蒋向前, Blunt L,等. 人工髋关节柄磨损评定中的三维表面形貌测量［J］. 应用基础与工程科学学报, 2012, 20 (1): 139-148.

    ZHANG H Y, JIANG X Q, BLUNT L, et al.. The application of 3D surface metrology in characterization of femoral stem wear ［J］. Journal of Basic Science and Engineering, 2012, 20(1): 139-148.(in Chinese)

[82] HE B F, PETZING J, WEBB P, et al.. Improving copper plating adhesion on glass using laser machining techniques and areal surface texture parameters ［J］. Optics & Lasers in Engineering, 2015, 75: 39-47.

[83] WHITEHOUSE D J. Function maps and the role of surfaces ［J］. International Journal of Machine Tools & Manufacture, 2001, 41(13): 1847-1861.

[84] 李丽伟, 董申, 程凯. 超光滑表面的加工、表征和功能［J］. 工具技术, 2002, 36(8): 15-18.

    LI L W, DONG S, CHENG K. Generation, Characterization and Function of Super-smooth Surfaces ［J］. Tool Engineering, 2002, 36(8): 15-18. (in Chinese)

[85] QI Q, LI T, SCOTT P J, et al.. A Correlational Study of Areal Surface Texture Parameters on Some Typical Machined Surfaces ［J］. Procedia CIRP, 2015, 27: 149-154.

[86] TODHUNTER L D, LEACH R K, LAWES S D A, et al.. Industrial survey of ISO surface texture parameters ［J］. CIRP Journal of Manufacturing Science & Technology, 2017,19: 84-92.