中国激光, 2018, 45 (4): 0402007, 网络出版: 2018-04-13   

悬垂圆孔激光选区熔化成形质量研究 下载: 592次

Research on Forming Quality of Overhanging Round Hole by Selective Laser Melting
段声勤 1,2刘婷婷 1,2,*廖文和 1,2张长东 1,2杨涛 1,2
作者单位
1 南京理工大学机械工程学院, 江苏 南京 210094
2 数控成形技术与装备国家地方联合工程实验室, 江苏 南京 210094
摘要
对圆孔试样进行分区分析, 研究了激光功率、扫描线角度以及轮廓扫描次数对悬垂圆孔结构成形质量的影响。结果表明, 激光功率对圆孔成形质量的影响显著, 随着激光功率的增大, 圆孔圆度值增大, 尺寸精度降低, 同时悬垂面出现细而长的熔池, 部分熔池断裂球化成球状熔滴; 当扫描线方向平行于悬垂面边缘线时, 悬垂面质量较好, 但在成形圆孔顶部近水平悬垂面处出现严重塌陷; 在设置的扫描次数范围内, 增加轮廓扫描次数可降低悬垂曲面表面粗糙度, 优化表面质量。
Abstract
By means of selective analysis for round hole specimen, the influences of laser power, scanning line angle and number of contour scans on the forming quality of overhanging round holes are investigated. The results show that, the laser power has a significant effect on the forming quality of round holes. With the increase of laser power, the roundness of round holes increases and the dimensional accuracy decreases. At the same time, there are many thin and long melt pools on the overhanging surface, and part of them are fractured into spherical droplets; the overhanging surface quality is better when the scanning line direction is parallel to the edge lines of the overhanging surface, but there occurs a serious collapse on the top of round holes and near to the horizontal overhanging surface. Within the setting number of scans, the increase of the number of contour scans can reduce the surface roughness of the overhanging surfaces and optimize the surface quality.

段声勤, 刘婷婷, 廖文和, 张长东, 杨涛. 悬垂圆孔激光选区熔化成形质量研究[J]. 中国激光, 2018, 45(4): 0402007. Duan Shengqin, Liu Tingting, Liao Wenhe, Zhang Changdong, Yang Tao. Research on Forming Quality of Overhanging Round Hole by Selective Laser Melting[J]. Chinese Journal of Lasers, 2018, 45(4): 0402007.

本文已被 4 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!