首页 > 期刊 > 栏目列表 > 栏目 (optical design and fabrication)

摘要

In order to fabricate a large-aperture continuous phase plate (CPP) using atmospheric pressure plasma processing (APPP) with high efficiency and precision, the position dwell mode and velocity mode were proposed and the iterative calculation method was developed for the non-constant removal rate. Two 320 mm × 320 mm × 2 mm CPPs were fabricated with two processing modes. The exp

PDF全文 Chinese Optics Letters | 2018,16(10):102201
分享:
0 87 262

摘要

Myopia has become a noteworthy issue due to the increasing use of our eyes. We propose a continuous power variation vision-training device based on Alvarez lenses with the power ranging from ?10 D to +2 D. First, we introduce the principle of Alvarez lenses and the evaluation method of dioptric power and astigmatism. Then, we optimize the optical system described by Zernike pol

PDF全文 Chinese Optics Letters | 2018,16(07):072201
分享:
0 100 392

摘要

Calcium fluoride is widely used in optical lithography lenses and causes retardation that cannot be ignored. However, few studies have been conducted to compensate for the retardation caused by calcium fluoride in optical lithography systems. In this Letter, a new index based on orientation Zernike polynomials is established to describe the value of retardation. Then, a method

PDF全文 Chinese Optics Letters | 2018,16(03):032201
分享:
0 123 267

摘要

We present a new compact radar system to measure a terahertz radar cross section (RCS) of metal plates, trihedral corner reflectors, and an aircraft scaled model with a 0.1 THz continuous wave. We both numerically and experimentally investigate the terahertz RCS of the metal plates and trihedral corner reflectors. The numerical simulations are obtained by using commercial softw

PDF全文 Chinese Optics Letters | 2017,15(11):112201
分享:
0 219 437

摘要

In this Letter, we present a novel design method of image-side telecentric freeform imaging systems. The freeform surfaces in the system can be generated using a point-by-point design approach starting from an initial system consisting of simple planes. The proposed method considers both the desired object–image relationships and the telecentricity at the image-side during the

PDF全文 Chinese Optics Letters | 2017,15(06):062202
分享:
0 255 796

摘要

A versatile nanosphere composite lithography (NSCL) combining both the advantages of multiple-exposure nanosphere lens lithography (MENSLL) and nanosphere template lithography (NSTL) is demonstrated. By well controlling the development, washing and the drying processes, the nanosphere monolayer can be well retained on the substrate after developing and washing. Thus the NSTL ca

PDF全文 Chinese Optics Letters | 2017,15(06):062201
分享:
0 272 476

摘要

This Letter reports the formation of periodic surface structures on Ni–Fe film irradiated by a single femtosecond laser pulse. A concave lens with a focus length of ?150 mm is placed in front of an objective (100×, NA=0.9), which transforms the Gaussian laser field into a ring distribution by the Fresnel diffraction. Periodic ripples form on the ablation area after the irradia

PDF全文 Chinese Optics Letters | 2017,15(02):022201
分享:
0 201 428

摘要

A method of multi-beam femtosecond laser irradiation combined with modified HF-HNO3-CH3COOH etching is used for the parallel fabrication of all-silicon plano-concave microlens arrays (MLAs). The laser beam is split by a diffractive optical element and focused by a lens to drill microholes parallely on silicon. An HF-HNO3-H2SO4-CH3COOH solution is used to expand and polish laser

PDF全文 Chinese Optics Letters | 2016,14(05):052201
分享:
0 269 1629

摘要

This Letter presents an optical design method based on the Seidel aberration theory for dynamic refocus systems. The function of a dynamic refocus system is to increase the amount of return photons when a pulsed laser travels over an extended height range. In this study, the dynamic refocus system is a short focal image system. The aberrations of the dynamic refocus system are

PDF全文 Chinese Optics Letters | 2016,14(04):042202
分享:
0 241 1339

摘要

The aim of this work is to provide an analytical method based on experimental measurements in order to obtain the prismatic film deformation for different curvatures of hollow cylindrical prismatic light guides (CPLGs). To conform to cylindrical guides it is necessary to bend the film to guide the light; changes induced by curving the film give rise to deformation shifts. Light

PDF全文 Chinese Optics Letters | 2016,14(04):042201
分享:
0 351 1163
首页上一页123456下一页尾页