现代显示, 2013, 24 (1-2): 43, 网络出版: 2013-03-01  

荧光粉涂覆方式对白光LED光色指标的影响

The Impact of Phosphor Coating Method on the White LED Performance
作者单位
桂林电子科技大学机电工程学院,广西 桂林 541004
摘要
文章采用TRACEPRO软件建立了三种白光LED的光学模型:(1)芯片直接涂覆荧光粉;(2)芯片涂覆硅胶后涂覆荧光粉层;(3)芯片涂覆荧光粉后涂覆硅胶层。通过改变荧光粉的摩尔浓度或硅胶厚度来考察白光LED的光色指标,如光通量、色温及显色指数的变化。研究结果表明:第一种和第二种涂覆方式中,光色指标随着荧光粉摩尔浓度或硅胶厚度的改变呈规律性变化;第三种涂覆方式中,色温及显色指数的变化趋势不稳定,第三种方式光通量高于前两种,最大值可达到87.3 lm。三种方式的显色指数在70左右。研究结论为白光LED工艺设计提供参考和依据。
Abstract
In this paper, the TRACEPRO software was used to establish three white LED optical models: (1) chip with directly coated phosphor, (2) chip with coated silica gel then with a phosphor layer, (3) chip with coated phosphor then with a silica gel layer. The influence of the phosphor concentration or silicone layer thickness on the white LED luminous flux, color temperature and color rendering index (CRI) was studied, respectively. The simulations show that for the first and second phosphor coating methods, luminous flux, color temperature and color rendering index change regularly with the phosphor concentration or silica gel thickness. For the third coating method, the color temperature and color rendering index have an unstable trend with the phosphor concentration or silica gel thickness. The luminous flux of the third phosphor coating LED is higher than that of the mentioned above two methods LED, which reaches 87.3lm. The CRI of the three coating LED is about 70. The results provide the reference and basis for white LED process design.
参考文献

[1] Liu Zong-Yuan, Liu Sheng, et al. Studies on optical consistency of white LEDs affected by phosphor thickness and concentration using optical simulation[J]. IEEE Trans, 2010, 33(4): 680-687.

[2] Yuan-Chang Lin, Jiun Pyng You, et al. Packaging of phosphor based high power white LEDs: effects of phosphor concentration and packaging configuration[J]. J. Electronic Packaging, 2011. 133(011009): 1-5.

[3] Christian Sommer, Frank Reil, et al. The impact of light scattering on the radiant flux of phosphor-converted high power white light-emitting diodes[J]. J. Lightwave Technol, 2011, 29(15): 2285-2291.

[4] Christian Sommer, Frank Reil, et al. The impact of inhomogeneities in the phosphor distribution on the device performance of phosphor-converted high-power white LED light sources[J]. J. Lightwave Technol, 2010, 28(22): 3226-3232.

[5] Run Hu, Xiaobing Luo, Sheng Liu. Study on the optical properties of conformal coating light-emitting diode by monte carlo simulation[J]. IEEE Photon, 2011, 23(22): 1673-1675.

[6] 刘宗源. 大功率LED封装设计与制造的关键问题研究[D]. 武汉:华中科技大学,2010.

吴艳芳, 龚雨兵. 荧光粉涂覆方式对白光LED光色指标的影响[J]. 现代显示, 2013, 24(1-2): 43. WU Yan-fang, GONG Yu-bing. The Impact of Phosphor Coating Method on the White LED Performance[J]. ADVANCED DISPLAY, 2013, 24(1-2): 43.

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!