基于普通F-Theta透镜与远心F-Theta透镜的晶圆标识工艺的研究

为研究聚焦系统对晶圆标识工艺的影响, 搭建以1 066 nm的声光调Q脉冲光纤激光器为光源, 分别使用普通F-Theta透镜和远心F-Theta透镜的晶圆激光打标系统, 使用相同的工艺参数分别在晶圆表面进行点阵标识, 研究两种聚焦系统下晶圆的烧蚀阈值、离焦效果和点的形貌。采用白光干涉仪对晶圆标识区域的三维形貌进行评估, 研究发现普通F-Theta透镜与远心F-Theta透镜对晶圆的烧蚀阈值的影响区别不大。在离焦效果方面, 普通F-Theta透镜随着离焦量增加, 标识点直径逐渐变小; 而远心F-Theta透镜随着离焦量增加, 标识点直径先增大后减小。在打标范围内的标识质量方面, 两者在打标范围中心的标识质量基本相当, 离中心越远, 远心透镜也未能表现出更好的标识形貌。

Abstract

In order to study the influence of general F-Theta lens on telecentric F-Theta lens on wafer marking process, a wafer laser marking system using 1 066 nm acousto-optic Q-switched pulse fiber laser as light source and general F-Theta lens and telecentric F-Theta lens respectively is built. Dot matrix marking is carried out on the wafer surface with the same process parameters, and the ablation threshold, defocus effect and ablation plan of wafers under two F-Theta lenses are studied. Moreover, the three-dimensional morphology of wafer identification area is analyzed by white light interferometer. It is found that general F-Theta lens and telecentric F-Theta lens have little effect on the ablation threshold of wafers. In terms of defocusing effect, the ablation aperture of ordinary F-Theta lens decreases gradually with the increase of defocusing amount, while the ablation aperture of telecentric F-Theta lens first increases and then decreases with the increase of defocusing amount. In terms of the mark quality in the marking range, the mark quality of the two in the center of the marking range is basically the same, the farther away from the center, the telocentric lens does not show better mark morphology.

参考文献

[1] ZHANG L L, SHU T J, LI G Q, et al. Pulse shape controlled MOPA fiber laser for marking of Si wafer［C］//Proc SPIE 11907, Sixteenth National Conference on Laser Technology and Optoelectronics, ［S.I.］: SPIE, 2021, 11907: 587-593.

[2] ZHANG L L, SHU T J, LI G Q, et al. Processing study of laser marking on Si wafer［C］//Proc SPIE 11907, Sixteenth National Conference on Laser Technology and Optoelectronics, 2021, ［S.I.］: SPIE, 11907: 552-555.

[3] SHU T J, ZHANG L L, LI G Q, et al. Study on the process of laser marking for silicon wafer by 1060nm-MOPA laser［C］//Proc SPIE 11907, Sixteenth National Conference on Laser Technology and Optoelectronics, ［S.I.］: SPIE, 2021, 11907: 600-604.

[4] SCARONI J, MCKEE T. A close look at laser marking of silicon wafers［J］. Solid State Technology, 1997, 40: 245-251.

[5] 王旭琴, 孙靖, 李鹏, 等. 基于激光选区熔化的低畸变F-theta场镜设计［J］. 激光与红外, 2019, 49(4): 493-496.

[6] 王路. 精细激光扫描F-THETA透镜: CN202119964U［P］. 2012-01-18.

[7] 张登臣, 郁道银. 实用光学设计方法与现代光学系统［M］. 北京: 机械工业出版社, 1995.

[8] 陈海清. 现代实用光学系统［M］. 武汉: 华中科技大学出版社, 2003.

[9] YUREVICH V I, GRIMM V A, AFONYUSHKIN A A, et al. Optical design and performance of F-Theta lenses for high-power and high-precision applications［C］//SPIE Optical Systems Design. Proc SPIE 9626, Optical Systems Design: SPIE, 2015: Optical Design and Engineering VI, Jena, Germany. 2015, 9626: 437-452.

[10] BAUDACH S, BONSE J, KAUTEK W. Ablation experiments on polyimide with femtosecond laser pulses［J］. Applied Physics A, 1999, 69(1): S395-S398.

[11] 郎平, 徐阳阳, 袁晓帅, 等. 激光参数对硼磷合金铸铁缸套微坑形貌影响研究［J］. 应用激光, 2020, 40(3): 476-482.

舒天娇, 杜远超, 李国旗, 陈媛, 张玲玲, 马永新, 高垠芮, 胡豪威, 陈宇. 基于普通F-Theta透镜与远心F-Theta透镜的晶圆标识工艺的研究[J]. 应用激光, 2023, 43(2): 93. Shu Tianjiao, Du Yuanchao, Li Guoqi, Chen Yuan, Zhang Lingling, Ma Yongxin, Gao Yinrui, Hu Haowei, Chen Yu. Study on the Processing of Wafer Marking Based on General F-Theta Lens and Telecentric F-Theta Lens[J]. APPLIED LASER, 2023, 43(2): 93.

基于普通F-Theta透镜与远心F-Theta透镜的晶圆标识工艺的研究

关于本站 Cookie 的使用提示

全站搜索

基于普通F-Theta透镜与远心F-Theta透镜的晶圆标识工艺的研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索