应用光学, 2016, 37 (3): 435, 网络出版: 2016-10-20   

3片独立自由曲面式LED汽车近光灯光学设计

Optical design of 3 independent free-form surface LEDs automotive dipped headlamp
作者单位
1 江苏大学 机械工程学院, 江苏 镇江 212013
2 大茂伟瑞柯车灯有限公司, 江苏 常州 213022
摘要
为了使车辆驾驶员在夜间能够得到充足的照明, 并且避免对面会车司机眩目, 设计了具有明暗截止线的近光系统。根据GB25991-2010汽车用LED前照灯配光标准, 尝试使用大功率白光LED和结构简单、光学利用率高的自由曲面反射镜(FFR)来实现前照近光灯的设计。以非成像光学为理论基础, 建立了LED光源出射光角度和照明面上坐标的对应关系, 结合折反射定律计算自由曲面上点的坐标。合理划分基础面, 并优化调整各子面的面型数据, 实现配光要求。采用3颗LED共同实现近光功能, 每颗LED均有各自独立的光学系统。测试结果表明: 设计的光学系统效率达到54%, 且近光截止线清晰, 满足标准对各测试点照度的要求。
Abstract
In order to make sure of adequate lighting for the driver of the vehicle, and prevent the opposite driver from glare, an automotive dipped headlamp system with a cut-off line was designed. A dipped headlamp according to GB25991-2010 light distribution standard (automotive headlamps with LED light sources/or LED modules) was designed with high-power LED and free form reflectors (FFRs) which had simple structure and high optical efficiency. Based on the non-imaging optics theory, the correspondence between the angle of the light reflected by the freeform reflector and the coordinates of point in the target plane was established. The freeform lens point coordinates were calculated according to the correspondence of reflection and refraction laws. To achieve light distribution requirement, the fundamental surfaces were divided legitimately and the surface profile data of sub-surfaces were optimized and adjusted. The function of dipped headlamp was realized by 3 LEDs, each of which had its own independent optical system. The test results show that the optical system has a clear cut-off line, with the efficiency reaching 54%, which can fully meet the requirements of the illumination of regulation on each test point.
参考文献

[1] 苏胜君,陈祥熙,施伟斌,等.基于大功率LED的汽车多椭球前照灯设计[J].器件制造与应用, 2007, 32(8): 673-676.

    Su Shengjun, Chen Xiangxi, Shi Weibin, et al. Design of automobile ellipsoid headlight based on high power LED[J]. Manufacturing and Application of Device, 2007, 32(8): 673-676.

[2] 徐晨洁.LED汽车近光灯的光学设计[D].上海: 复旦大学, 2009.

    Xu Chenjie. Design of LED automotive dipped headlamp optical system[D]. Shanghai: Fudan University, 2009.

[3] 陈岩.现代灯具概要[M].北京: 轻工业出版社,1990.

    Chen Yan. Modern lamps and lanterns of profile[M]. Beijing: Light Industry Press,1990.

[4] 姜兆庆, 郭淑红, 祝云飞, 等.汽车前照灯配光性能测试方法的研究[J],中国学术期刊, 1996,1: 30-35.

    Jiang Zhaoqing,Guo Shuhong,Zhu Yunfei,et al. Research on test method of light distribution performance of automobile[J]. Chinese Academic Journals, 1996,1: 30-35.

[5] 朱维涛, 陈祥熙.汽车灯具设计原理与方法[J].光学仪器,2002,24(6): 35-41.

    Zhu Weitao, Chen Xiangxi. Design principles and methods of auto lamps and lanterns[J]. Optical Instruments, 2002, 24(6): 35-41.

[6] 中华人民共和国国家质量监督检验检疫总局.GB25991-2010 汽车用LED前照灯国家标准[S].北京: 中国标准出版社, 2011.

    People’s Republic of China General Administration of Quality Supervision, Inspection and Quarantine. GB25991-2010, Automotive headlamps with LED light sources and/or LED modules[S]. Beijing: China Standards Press Standards Press,2011.

[7] 黄佐贤.现代汽车灯具[M].北京: 长虹出版公司, 2003.

    Huang Zuoxian. The modern automobile lamps and lanterns[M]. Beijing: Changhong Publishing Company,2003.

[8] Roland W. Nonimaging optics[M]. Netherlands: Elsevier Academic Press, 2005: 62-120.

[9] 吴衡. 大功率LED汽车前照灯自由曲面光学系统[D]. 广州: 华南理工大学, 2012.

    Wu Heng. High power LED automobile headlight free form surface optical system[D].Guangzhou: South China University of Technology,2012.

[10] Zheng Zhenrong, Hao Xiang, Liu Xu, Freeform surface lens for LED uniform illumination[J]. Applied Optics, 2009, 48(10): 6627-6634.

[11] Wang Lin. Discontinuous free-form lens design for prescribed irradiance[J]. Applied Optics, 2007, 47(18): 3716-3723.

[12] Ong P T, Gordon J M, Rabl A, et al. Tailored edge-ray designs for uniform illumination of distant targets[J]. Opt. Eng., 1995, 34(6): 1726-1737.

[13] Timinger A,Muschaweck J, Ries A. Designing tailored free-form surfaces for general illumination[J]. SPIE, 2003,5186: 128-132.

姚红兵, 王单单, 辛忠华, 徐进, 刘敏. 3片独立自由曲面式LED汽车近光灯光学设计[J]. 应用光学, 2016, 37(3): 435. Yao Hongbing, Wang Dandan, Xin Zhonghua, Xu Jin, Liu Min. Optical design of 3 independent free-form surface LEDs automotive dipped headlamp[J]. Journal of Applied Optics, 2016, 37(3): 435.

本文已被 3 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!