Importance of limiting hohlraum leaks at cryogenic temperatures on NIF targets
1 Introduction
It is well recognized that the bane of cryogenic operations is the maintenance of near perfect vacuum in the chamber that separates the cold components from the one at room temperature (RT). If the vacuum is compromised, convective heat transfer between the warm and cold surfaces can greatly affect the ability to control the temperature of either. In this paper, we discuss our work of making so-called targets for inertial confinement fusion (ICF) experiments leak-tight at cryogenic temperatures to meet the stringent requirements of these experiments. These targets are in fact complex, micro-assembled systems that contain the hydrogen fuel for testing the fusion process using laser energy as the driving force. These experiments, or shots, are performed at the National Ignition Facility (NIF), where 192 beams can deliver almost 2 MJ of energy into the target[1].
Typical NIF targets are composed of three essential physics components—a hohlraum which is a can-shaped component made of a high atomic number (high Z) material such as gold, a spherical ablator capsule which is composed of a low Z material such as plastic, carbon or beryllium and the hydrogen fuel inside the capsule[2]. This is shown in the schematic seen in Figure
Fig. 1. Schematic of the core part of an ICF target showing the hohlraum, capsule ablator and the DT ice. The laser beams impinge on the hohlraum walls and provide the energy for the fusion reaction.
Specifically, the hydrogen fuel is composed of its isotopes deuterium and tritium (DT). These are present inside the capsule as a frozen DT ice layer, made using a careful ‘layering’ process[3–7]. It is important to realize the length scales involved: typical dimensions are about 2 mm for the capsule diameter and 70 um for the ice layer thickness. The fusion process is critically dependent on getting enormous compression of the fuel to ultra-high densities[8]. This is achieved through an implosion caused by absorption of X-rays by the capsule. These X-rays are generated by the hohlraum as it is exposed to the laser beams. Mixing of the capsule material into the hydrogen fuel during the implosion quenches the reaction and can curtail the fusion event, hence Rayleigh–Taylor instabilities are extremely deleterious[9]. These instabilities are known to be triggered by various surface and bulk roughness and density variations in the ablator and the ice layer[10].
For the purposes of this discussion, we are concerned specifically about achieving as smooth and homogeneous a DT ice layer as possible. Smoothness can be quantified in terms of spectral density functions and grouped into two overall categories of low-mode and high-mode roughness[6]. Low-mode roughness is more related to how round and uniform the DT ice layer is and hence is dictated by the thermal environment surrounding the capsule. In order to meet a specification of sub-micron low-mode roughness[6], calculations suggest that the control of the thermal environment needs to be better than 0.5 mK[11]. This underlines the need for stringent temperature control inside the hohlraum chamber which holds the capsule in its center secured between two 30 nm membranes. The tight control of the temperature field is the primary objective of work discussed below.
For tamping purposes, the hohlraum is filled with a gas such as He, typically at sub-atmospheric pressures. As described in more detail later, we cool the hohlraum by conductively connecting it to the cryostat and the He inside also serves to cool the capsule accordingly. When the target is fielded on NIF, it is held at high vacuum within a shroud, which is a clamshell structure that protects the target from the ambient till close to shot time at which point the shroud is splayed open allowing full visibility of the target to the laser beams (Figure
Fig. 2. Sketch and photograph (upper left) showing the clamshell shroud that shields the target from the ambient outside during the layering process.
In an ideal situation, the He contained inside the hohlraum is stagnant whereby only the cooling and heating devices strategically placed on the target control the temperature field within the hohlraum. However, if there is a leak in the hohlraum chamber due to a failure of some sort, it is necessary to assess the limiting rate of escape of the He gas that would violate the requirements for DT ice layering.
Before proceeding to the calculations of the acceptable leak rate, it is helpful to review the essential fabrication details of the target. As stated earlier, at the core of the target is a capsule suspended at the center of the hohlraum can via tenting membranes. The real target however is far more complex[14, 15] as seen in Figure
Fig. 3. Target is a micro-assembly of many components, some of which are shown above. There are several temperature sensors and heaters, though only one set is shown above.
One reason for this is the requirement for high-dimensional fidelity. Since the hohlraum is a thin (about
2 Leak rate specification
In order to expedite the manufacture of these assemblies, we need to derive a leakage specification that we believe will not impact the performance of the target. To do so we consider several factors below. It is useful to note that the typical amount of gas in the hohlraum at fielding temperature of about 18.3 K is given by:
At RT, we expect to observe small amounts of He gas flow out of hohlraum assemblies due to permeation through the various polymer elements used in the target (primarily windows and glue bonds). But as the target is cooled to deep cryogenic conditions, permeation is completely cut out and any He loss occurs only through small leaks in the many glue joints in these systems. We now consider the impact of this leak on the thermal performance of the system.
Heat load on the hohlraum due to warm gas flowing in to hold the pressure constantChange in the flow velocity of the gas in the hohlraumLimit on the amount of He that can be leaked into the target chamberConduction from the clamshell shroud to the target
A rough estimate of the temperature drop as a function of target assembly leak rate computed using a finite element model is shown below. The temperature drop is a function of the gas heat conduction to the hohlraum surface, the heat conductance between the hohlraum surface and the cooling rings. The gas heat conduction is determined by the pressure and species of the gas. The pressure is a function of the leak rate and the combined conductance of the ‘escape’ paths that allow for the gas to be released from the shroud enclosure. It is assumed that the only significant escape path is via the
It is useful to mention here that radiative heating of the target is controlled using cold shields and reflective windows. The clamshell shroud that surrounds the target is made of two sections: an outer shell which is not cooled and an inner shell that is maintained at about 125 K. Windows on the shroud are gold coated such that virtually all the IR radiation is reflected while still permitting transmission of visible radiation to enable alignment of the target. In this design, the radiative load on the target is negligible.
Considering all of these perspectives together, the limiting factor is the heat load on the hohlraum brought in by the warm gas to hold He pressure constant. Hence, we propose that the upper limit for leak rate specification is
It must be noted that the fuel is transported into the capsule through a
The upper limit of
Fig. 4. Matching the model and the data using a $25~\unicode[STIX]{x03BC}\text{m}$ diameter orifice.
This now allows us to get a measure of the computed orifice size as a function of any leak rate (Figure
Fig. 5. Relationship between an orifice diameter and the corresponding flow rate at 18 K and 450 torr upstream pressure.
This demonstrates how challenging it is to find the source an unacceptably high leak.
3 Target failures
As NIF has become fully operational as a national user facility, experiments are scheduled as frequently as possible[1]. On average, one cryogenic target is required per week day. Some of these are not used for DT ice layering but instead for studies that aid the understanding of the fusion reaction. As stated above, targets are held together using adhesives. Some of these bonds are made with the help of a micromanipulator but majority are done by hand due to the small volumes that need to be dispensed in hard to reach geometries.
For a successful target, all of the pores in those bonds that hold the TMPs and associated components together need to have a cumulative area smaller than that of a
Of greater concern, however, are stresses caused by mismatch in contraction of the different materials at these joints upon cooling to cryogenic temperatures that can cause mechanical failure of the adhesive and a resultant leak. Through careful selection of adhesives, we have achieved requisite high proofing yield (
Failures can be binned into two broad categories: recurring ones and sporadic ones. The latter type are often due to a mishap or an extenuating circumstance during assembly and by definition, do not repeat over time. It is the former that requires serious attention. Often these failures assume epidemic proportions as they occur due to subtle process drifts and are challenging to unravel.
4 Example of a recurring leak problem on NIF targets
In this section, we describe the investigation of failures due to hohlraum leaks to illustrate the type of in-depth analysis that is frequently called for. After a prolonged period of high yield production, as is the norm, there was a sudden onset of a specific type of leak which then continued to occur with alarming regularity. An immediate review of the assembly processes showed that there was nothing notably different and needed rectification. Since targets are produced at the rate of one per day, an event such as this tends to cripple the output with no end in sight till the right root cause is identified and resolved.
Identification of the location of a leak is often the first major hurdle, especially as it is not possible to put the whole target in an electron microscope without stressing the many membranes used within. Thus, we needed try to use other clues and methods to help hone in onto probable locations. In this case, the leaks had this characteristic behavior: initially, at RT, the hohlraum behaved normally showing nominal He permeation, then failure at cryogenic temperatures upon cooling with very high leak rates (
The question, of course, is at what location? One possibility is using the concept of a sniffer test with a capillary where a local area is puffed briefly with He. But the facts that the target cannot handle high pressure differential and that the leak effectively disappears at RT make that practically impossible. Thorough inspection of the target with an optical microscope revealed nothing specific, which is not surprising.
But there was one peculiar feature to this leak behavior that provided a further clue. We can see this in Figure
Fig. 6. Results from the cryogenic proofing of the hohlraum at cryogenic temperature. The solid blue line is the supply line pressure while the dotted blue line is that of the return line. The red dots are the corresponding leak rate. Both lines are open to the hohlraum after 1000 s.
In order to understand the plot, it is necessary to briefly describe the proofing algorithm for the hohlraum. Starting with the target at vacuum at
As seen in Figure
It is helpful to review the essential steps in assembling the window to the TMP. Recall that the functional portion of the LEH window is the 500 nm polyimide membrane with a 25 nm of Al on top. The Al helps to restrict the entrance of IR radiation into the hohlraum chamber as it can interfere with the layering process. These windows are fabricated by Luxel Corporation and supplied on a
Fig. 7. Schematic of the TMP window washer to Al TMP bonding design. The picture on the right is an image of the typical LEH bonding operation.
The gap can then be filled with a low viscosity UV cured adhesive through capillary action. This provides a deterministic method for generating a well-controlled circular fillet of adhesive that can be exposed to light. Given that this process was successfully used to make over 1400 window assemblies before failures appeared, it naturally begs the question as to what triggered these failures?
5 Failure analysis
When one such failed LEH window region was inspected in the SEM, a small section of the circular bondline showed the presence of dark bands (Figure
Fig. 8. SEM images of features seen in the LEH to TMP bondline of a failed target. The red circle highlights the arc where dark bands, like the one seen in the lower left, were seen. These bands were seen to be linear holes in the bondline (image on the right).
They were not seen in the windows that did not leak. Upon high-resolution imaging, it was seen that these bands were linear holes in a glue fillet, but it was not clear how deep these holes were and as such, exactly what the leak path was. In order to determine that, we needed to cross section the region of interest in such a manner that the procedure itself would not obscure the evidence in any way. One method that is custom-made for this procedure is localized etching with a focused gallium ion beam (FIB). Figure
Fig. 9. SEM image of the FIB etched section showing the internal cross-section of the region under the band seen in Figure 8 .
Interestingly, the image reveals a gap running along the Al TMP wall over almost the entire height of the fillet.
One obvious cause for this gap is the generation of tensile stresses in the fillet. The CTE of Al at RT is 23 ppm/K whereas that of the adhesive is about 70 ppm/K. Even though CTE value drops with decreasing temperature, the RT CTE value is a good indicator of the disparity between any two materials in this respect. Curiously, the specific configuration encountered in this case leads to different behavior on each of the two Al surfaces. Due to its greater propensity to shrink relative to Al, the circular glue fillet exerts a compressive stress at the inner interface (i.e., the LEH washer) and simultaneously a tensile stress on the outer one (i.e., the TMP surface). The magnitude of this stress
This yields a tensile stress of 11 MPa exerted during cool down. If this were to exceed the interfacial strength of the bond, we would see delamination failure. Since interfacial strengths are extremely dependent on the surface energy of the substrate which can be easily altered by the exact processing history or invisible contamination, this is a viable mechanism. It is certainly consistent with the gap seen only on the side facing the TMP wall. The implication of this would be that greater attention would need to be paid to the surface preparation for return to high yield.
Whereas the above argument is seemingly convincing and often true, it is imperative to look carefully at the details seen in the image. In particular, we see that the width of the gap is about
Re-examining what else can create a gap, the only other mechanism that can be invoked is shrinkage during curing. Typical acrylic adhesives shrink 3% to 4% linearly[18]. The thickness of the adhesive layer is about
In effect, the curing of free surface prior to full internal solidification imposes a constraint on where the shrinkage can occur. Shrinkage now has to happen internally and it does so along the shadowed wall. Upon inquiry, it turned out that the operation had indeed been modified recently to occasionally include a top down viewing of the exposure process with a microscope that forced the UV curing beam to be incident from the side and hence at an angle the TMP. The procedure had not formally called out for a vertical exposure, though it was the practiced norm for several years. A new operator presumed the tilting to be a benign enough modification and as a result, it was completely overlooked as a change during process review.
The final check was to correct the problem and validate the hypothesis. We installed a fixture that allowed the wand to be placed only at an orthogonal angle and at the right distance. Figure
Fig. 11. Plot showing the cumulative failures as a function of number of the targets built, representing a snapshot in time in target production. Note that the first instance of failure was around target 25. The installation of the fixture for vertical curing was implemented at target # 119, after which the failures stopped.
This served as the ultimate verification of the hypothesis.
Our goal of documenting this is to underline the subtlety involved in coming up with the exact cause for failure in this case. This has been equally true for other cases not mentioned here. This entire episode played out over about 4 months. About 30 days from the first failure, we had statistical data to say that the failure mode was not random fluctuation. Off-line testing and analysis took about 2 more months. While the implementation of solution was done quickly, to establish its sustained success meant another month of testing.
An important lesson to be learned from this is importance of any complex, multi-step production process to stay completely true to the established protocols. Corporations such as Intel have been known to espouse this principle when increasing throughput through expansion of production lines (replicate-everything-exactly motto). Likewise, it is equally important to specify the range of tolerance of the various steps when the process is being defined early on, particularly if it involves human operation. Drifts in procedures can cumulatively become a significant change over time. Designing fixtures to standardize is a great solution to this issue but can also be prohibitively expensive. When this is the case and failures happen, process reviews need to be rigorous and exacting.
6 Summary
ICF targets present interesting material challenges, one of the biggest of which is making sure that the thermal stresses that develop due the mismatch in coefficients of thermal expansion do not lead to failures in the numerous bonds. In this paper, we discuss the different factors that need to be considered to be able to specify the maximum flow rate allowed if a failure were to result in a leak at the operating temperature of
[1]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
Article Outline
Suhas Bhandarkar, Nick Teslich, Ben Haid, Evan Mapoles. Importance of limiting hohlraum leaks at cryogenic temperatures on NIF targets[J]. High Power Laser Science and Engineering, 2017, 5(3): 03000e19.