不同杨氏模量对复合材料储能飞轮应力及位移影响之比较

李成; 万志超; 郑艳萍; 铁瑛

光学精密工程, 2009, 17 (7): 1609, 网络出版: 2009-10-28

不同杨氏模量对复合材料储能飞轮应力及位移影响之比较

Comparison of effects of different young's moduli on stress and displacement of composite flywheel

论文大纲

李成 ^1,*万志超 ²郑艳萍 ¹铁瑛 ¹

作者单位

¹ 郑州大学机械工程学院,河南郑州 450001

² 漯河医学高等专科学校,河南漯河 462002

复合材料储能飞轮杨氏模量应力位移 composite material flywheel for energy storage Young's Modulus stress displacement

摘要

对不同杨氏模量对复合材料飞轮的应力、位移分布的影响进行了研究。结合复合材料飞轮转子的结构特点,根据非均质各向异性弹性理论建立计算模型,得到飞轮在工作转速情况下应力和位移计算的解析公式,给出了任一点的径向、环向应力及径向位移。按照所建立的计算模型,讨论了具有不同杨氏模量的复合材料对径向、环向应力和径向位移的影响,仿真分析了复合材料飞轮转子在不同边界条件、几何参数情况下的应力和位移。结果表明:随着角速度从0增大到5 000 rad/s,径向应力、环向应力和径向位移都增大;两种材料径向应力的最大值都出现在飞轮的外缘,最大环向应力都出现在飞轮的内侧;高杨氏模量(Er=100 GPa,Eθ=350 GPa)时的径向和环向应力都要大于低杨氏模量时(Er=20 GPa,Eθ=150 GPa)的情况,而位移则是在低杨氏模量的情况下较大。

Abstract

The influences of different Young's moduli on the distribution of the stress and displacement of a composite flywheel was investigated in this paper.According to the heterogeneous anisotropy elastic theory and design features of the flywheel,the computation formulas for the stress and displacement of the composite flywheel were established at working speeds,and the radial stress,circumferential stress and radial displacement at an arbitrary point were presented.Then,based on the computation models above,the influences of different positions and rotational speeds on the radial stress,circumferential stress and radial displacement were discussed.It is concluded that the radial stress,circumferential stress and radial displacement all increase with increasing of angular velocity from 0 to 5 000 rad/s.The maximal radial stresses of two kinds of materials all occur at the exterior margin of flywheel and the maximal circumferential stresses occur at the inner margin of flywheel.Moreover,under the situation of high Young's moduli(Er=100 GPa,Eθ=350 GPa),radial and circumferential stresses are all higher than that of low Young's moduli (Er=20 GPa,Eθ=150 GPa),whereas,the displacement shows an oppisite change.

参考文献

[1] JEROME T,RYAN E,PAUL M.Composite flywheels for energy storage[J].Composites Science and Technology,2006,66:2520-2627.

[2] 宫能平,夏源明,毛天祥.复合材料飞轮的三维应力分析[J].复合材料学报,2002,19(1):113-116.

GONG N P,XIA Y M,MAO T X.Design of composite flywheel structure and its stress analysis[J].Acta Materiae Compositae Sinica,2002,19(1):113-116.(in Chinese)

[3] 李雯,张力.复合材料飞轮的应力分析[J].汽车技术,2004(5):29-32.

LI W,ZHANG L.Stress analysis of composite material flywheels[J].Automobile Technology,2004(5):29-32.(in Chinese)

[4] 杨鼎宁,邹经湘.储能飞轮过盈/脱落过程研究[J].机械工程学报,2003,39(4):145-150.

YANG D N,ZOU J X. Study on interference fit and separation process of flywheel for energy storage[J].Chinese Journal of Mechanical Engineering,2003,39(4):145-150.(in Chinese)

[5] WANG L,REN X J,SHATIL G.Assessment of fatigue and fracture strength of transportation energy storage flywheel using finite element simulation[J].Structures and Materials,2003(12):235-244.

[6] 刘怀喜,赵程,张恒.复合材料飞轮断裂与损伤的研究[J].机械强度,2005,27(5):714-718.

LIU HX,ZHAO C,ZHANG H.Research of fracture and damage on the composite flywheel[J].Journal of Mechanical Strength,2005,27(5):714-718.(in Chinese)

[7] 杨橙,马力,王仲范.汽车飞轮电池中高速复合材料飞轮的有限元分析[J].武汉理工大学学报,2002,24(2):112-115.

YANG C,MA L,WANG Z F.Finite element Analysis of composite material flywheels with high speed in electric vehicle flywheel batteries[J].Journal of Wuhan University of Technology,2002,24(2):112-115.(in Chinese)

[8] 秦勇,夏源明,毛天祥.纤维束张紧力缠绕复合材料飞轮初应力的三维数值分析[J].复合材料学报,2005,22(4):149-155.

QIN Y,XIA Y M,MAO T X.3D numerical analysis of initial stress of composite flywheel fabricated by filament tension winding[J].Acta Materiae Compositae Sinica,2005,22(4):149-155.(In Chinese)

[9] ANDREW C,CHARLES E.Optimal design of press-fitted filament wound composite flywheel rotors[J].Composite Structures,2006,72:47-57.

[10] XU X L,YU Z W.Failure analysis of diesel engine flywheel ring-gears[J].Engineering Failure Analysis,2005(12):25-34.

[11] ARNOLD S,SALEEB A.Deformation and life analysis of composite flywheel disk systems[J].Composites: Part B 33,2002:433-459.

[12] MUβCHELISCHWILI N L.Einige Grundaufgaben zur mathematischen Elastizittstheorie[M].München: Carl Hanser Verlag,1971

李成, 万志超, 郑艳萍, 铁瑛. 不同杨氏模量对复合材料储能飞轮应力及位移影响之比较[J]. 光学精密工程, 2009, 17(7): 1609. LI Cheng, WAN Zhi-chao, ZHENG Yan-ping, TIE Ying. Comparison of effects of different young's moduli on stress and displacement of composite flywheel[J]. Optics and Precision Engineering, 2009, 17(7): 1609.

不同杨氏模量对复合材料储能飞轮应力及位移影响之比较

关于本站 Cookie 的使用提示

全站搜索

不同杨氏模量对复合材料储能飞轮应力及位移影响之比较

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索