K418与42CrMo异种金属的激光穿透焊接

庞铭; 虞钢; 刘兆; 郑彩云; 王立新; 宁伟健

中国激光, 2006, 33 (8): 1122, 网络出版: 2006-08-31

K418与42CrMo异种金属的激光穿透焊接

Dissimilar Metal of K418 and 42CrMo Full Penetration Laser Welding

论文大纲

庞铭 ^*虞钢刘兆郑彩云王立新宁伟健

作者单位

中国科学院力学研究所, 北京 100080

激光技术激光焊接穿透焊焊缝 laser technique laser welding full penetration welding weld seam

摘要

实验研究了连续波Nd∶YAG激光焊接速度、侧吹保护气流量和离焦量等参量对激光穿透焊接K418和42CrMo焊缝成形的影响。结果表明,K418与42CrMo激光穿透焊接有X形和T形两种典型的焊缝形貌,且焊缝形貌是不对称的。随着焊接速度的提高,焊接线能量降低,焊缝尺寸变小, 且焊缝上部尺寸变化比下部尺寸变化慢,焊缝形貌由X形过渡到T形。当离焦量在瑞利长度范围内时,焊缝正面宽度变化很小；当离焦量超出瑞利长度范围时,在足够高的激光功率密度下,焊缝正面宽度快速增加。在激光功率为3 kW,侧吹保护气角度为35°条件下,通过优化焊接速度、侧吹保护气流量和离焦量等参量可以得到最佳焊缝质量。

Abstract

The influences of laser welding velocity, flow rate of side-blow shielding gas, defocusing distance and other parameters on the full penetration laser weld seam of K418 and 42CrMo were experimentally investigated using continuous wave Nd∶YAG laser. Results show that the asymmetric cross-sections of weld seams exhibit X shape or T shape. With increasing welding velocity, the linear heat input and dimension of weld seam decrease, and the shape of it changes from X shape to T shape. Meanwhile, the rate of change in dimension of weld bottom region is larger than that of weld top region. The change of the top surface width of the weld seam is small under the condition that defocusing distance changes within the range of Rayleigh length; the top surface widths of the weld seam increase quickly under the condition that defocusing distance changes out of the range of Rayleigh length with enough density of laser power. The high-quality of weld seam with constant 3 kW laser power and 35° angle of side-blow shielding gas can be obtained by optimizing welding velocity, flow rate of shielding gas, defocusing distance and other parameters.

参考文献

[1] . W. Lee. Inertia friction welding of a gas turbine rotor[J]. Welding Review International, 1992, 11(4): l89-192.

[2] . . On strengthening the friction welding joint between K418 turbo disk and 42CrMo shaft[J]. Journal of Northwestern Polytechnical University, 2004, 22(1): 112-115.

[3] . Sun, J. C. Ion. Review laser welding of dissimilar metal combinations[J]. Journal of Materials Science, 1995, 30: 4205-4214.

[4] . .. Laser welding of stainless steel[J]. Electric Welding Machine, 2002, 32(6): 23-25.

[5] Wang Jiachun, Wang Xizhe, Hui Songxiao. Research of linear heat input and laser focus position for laser welding HE130 titanium alloy [J]. Chinese J. Lasers, 2003, 30(2):179～184
王家淳,王希哲,惠松骁. HE130合金激光焊接线能量与焦点位置研究[J]. 中国激光, 2003, 30(2):179～184

[6] Lü Baida. Laser Optics-Laser Beam Propagation and Beam Quality Control [M]. Chengdu: Sichuan University Press, 1992. 63～64
吕百达. 激光光学-激光束的传输变换和光束质量控制[M]. 成都：四川大学出版社,1992. 63～64

[7] Xiong Jiangang, Hu Xiyuan, Chen Zutao et al.. Study on laser welding of cast-base superalloy [J]. Chinese J. Lasers, 1996, A23(12):1107～1111
熊建钢,胡席远,陈祖涛等. 激光焊接铸造镍基高温合金工艺研究[J]. 中国激光, 1996, A23(12):1107～1111

[8] Shen Huitang. Welding Technique and Means [M]. Beijing: China Machine Press, 2003. 271～273
沈惠塘. 焊接技术与高招[M]. 北京：机械工业出版社, 2003. 271～273

[9] Yu Gang, Yu Heji. Integrated Laser Intelligent Manufacturing [M]. Beijing: Metallurgy Industry Press, 2001. 124～125
虞钢,虞和济. 集成化激光智能加工工程[M]. 北京：冶金工业出版社,2001. 124～125

[10] Abel-Monem, Ei -Batahgy. Effect of laser welding parameters on fusion zone shape and solidification structure of austenitic stainless steels [J]. Materials Letters, 1997, 32(2,3):155～163

[11] . Weld shaping for laser fully penetration welding titanium alloy[J]. Transactions of the China Welding Institution, 2004, 25(5): 74-77.

[12] Hu Changkui, Chen Peifeng, Liang Jun. The technic study of laser welding thick plates [J]. Applied Laser, 2003, 23(5):268～270
胡昌奎,陈培锋,梁军. 激光焊接厚钢板的工艺研究[J]. 应用激光, 2003, 23(5):268～270

[13] Qin Guoliang, Lin Shangyang. Radial dimension of keyhole and its dynamic characteristics in laser deep penetration welding [J]. Chinese J. Lasers, 2005, 32(4):557～561
秦国梁,林尚扬. 激光深熔焊接过程中小孔径向尺寸及其动特性[J]. 中国激光, 2005, 32(4):557～561

庞铭, 虞钢, 刘兆, 郑彩云, 王立新, 宁伟健. K418与42CrMo异种金属的激光穿透焊接[J]. 中国激光, 2006, 33(8): 1122. 庞铭, 虞钢, 刘兆, 郑彩云, 王立新, 宁伟健. Dissimilar Metal of K418 and 42CrMo Full Penetration Laser Welding[J]. Chinese Journal of Lasers, 2006, 33(8): 1122.

K418与42CrMo异种金属的激光穿透焊接

关于本站 Cookie 的使用提示

全站搜索

K418与42CrMo异种金属的激光穿透焊接

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索