激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究

麦淑珍; 杨永强; 王迪

doi:doi:10.3788/cjl201542.1203004

中国激光, 2015, 42 (12): 1203004, 网络出版: 2015-12-01

激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究下载： 802次

Study on Surface Morphology and Roughness Variation of NiCr Alloy Curved Surface Manufactured by Selective Laser Melting

论文大纲

麦淑珍 ^*杨永强王迪

作者单位

华南理工大学机械与汽车工程学院, 广东广州 510641

AI 词云图 AI语音精读 AI语音超短摘要

注：本部分内容由 AI 自动生成，请您知悉。

摘要

为快速直接制造具有复杂曲面的个性化金属零件，需要保证激光选区熔化(SLM)成型曲面特征的表面成型质量。通过正交实验获得NiCr 合金优化工艺参数，采用S 型正交层错扫描策略成型两种柱面体模型；在超景深显微镜、扫描电镜下观察成型件内、外侧曲面表面形貌，并测量相应表面粗糙度。结果表明：成型不同空间位置摆放的曲面零件，各层面轮廓误差、层面间台阶效应的逐层堆叠最终使曲面形成台阶状、网结状形貌，成型倾斜切角小于60°的悬垂曲面时因粉末粘附严重甚至会形成条虫状、粒球状形貌；表面粗糙度Ra值与曲面特征表面形貌变化规律具有相关性，这为提高SLM 成型曲面零件的表面成型质量提供了重要参考。

Abstract

In order to directly fabricate customized metallic parts with complicated surface, the surface quality of curved surface feature manufactured by selective laser melting (SLM) technology should be ensured. The parameters of NiCr alloy are optimized by orthogonal experiment and two kinds of cylinders are fabricated with X-Y inter-layer staggered scan strategy. The surface morphologies of curved surfaces of the parts are studied using three dimensional super depth digital microscope and scanning electron microscope, and the corresponding surface roughness is measured. The results show that when fabricating the parts with curved surface placed in different spatial positions, contour error in layer and stair effect among layers stacked lead to the staircase-shaped profile and anastomosing morphology on curved surfaces, and even the worm-like or granular morphology on overhanging curved surfaces when the tilt angle is larger than 60° . Variation of the value of Ra is consistent with surface morphology. The results provide important guidance to improve surface quality of the parts with curved surface fabricated by SLM.

参考文献

[1] 史玉升, 鲁中良, 章文献, 等. 选择性激光熔化快速成形技术与装备[J]．中国表面工程, 2006, 19(5): 150-153.

Shi Yusheng, Lu Zhongliang, Zhang Wenxian, et al.. The technology and equipment of selective laser melting[J]. China Surface Engineering, 2006, 19(5): 150-153.

[2] 吴伟辉, 杨永强, 毛桂生. 316 L选区激光熔化增材制造熔池搭接堆积形貌分析[J]. 制造技术与机床, 2014, (4): 46-49.

Wu Weihui, Yang Yongqiang, Mao Guisheng. Morphology analysis of molten pools lapping and accumulation in selective laser melting of 316L stainless steel[J]. Manufacturing Technology & Machine Tool, 2014, (4): 46-49.

[3] 王赟达, 杨永强, 宋长辉, 等．基于响应面法优化激光选区熔化成型CoCrMo合金工艺及其电化学行为[J]．中国有色金属学报, 2014, 24(10): 2497-2505.

Wang Yunda, Yang Yongqiang, Song Changhui, et al.. Process optimization and electrochemical behavior of CoCrMo alloy fabricated by selective laser melting based on response surface method[J]. The Chinese Journal of Nonferrous Metals, 2014, 24(10): 2497-2505.

[4] 宋长辉, 杨永强, 叶梓恒, 等. 基于选区激光熔化快速成型的自由设计与制造进展[J]. 激光与光电子学进展, 2013, 50(8): 080026.

Song Changhui, Yang Yongqiang, Ye Ziheng, et al.. Development of freeform design and manufacturing based on selective laser melting [J]. Laser & Optoelectronics Progress, 2013, 50(8): 080026.

[5] Wehmoller M, Warnke P H, Zilian C, et al.. Implant design and production-a new approach by selective laser melting[C]. International Congress Series, Elsevier, 2005, 1281: 690-695.

[6] Campbell I, Bourell D, Gibson I. Additive manufacturing: Rapid prototyping comes of age[J]. Rapid Prototyping Journal, 2012, 18(4): 255-258.

[7] 陈小东, 邢文忠. 快速成型技术及其在口腔修复中的应用[J]. 中国实用口腔科杂志, 2013, 6(6): 326-330.

Chen Xiaodong, Xing Wenzhong. Rapid prototyping technology and its application in prosthodontics[J]. Chinese Journal of Practical Stomatology, 2013, 6(6): 326-330.

[8] 王迪, 刘睿诚, 杨永强. 激光选区熔化成型免组装机构间隙设计及工艺优化[J]. 中国激光, 2014, 41(2): 0203004.

Wang Di, Liu Ruicheng, Yang Yongqiang. Clearance design and process optimization of non-assembly mechanisms fabricated by selective laser melting[J]. Chinese J Lasers, 2014, 41(2): 0203004.

[9] 李瑞迪, 魏青松, 刘锦辉, 等. 选择性激光熔化成形关键基础问题的研究进展[J]. 航空制造技术, 2015, (5): 26-31.

Li Ruidi, Wei Qingsong, Liu Jinhui, et al.. Research progress of key basic issue in selective laser melting of metallic powder[J]. Aeronautical Manufacturing Technology, 2015, (5): 26-31.

[10] Wang D, Yang Y Q, Zhang M H, et al.. Study on SLM fabrication of precision metal parts with overhanging structures[C]. Assembly and Manufacturing (ISAM), IEEE, 2013: 222-225.

[11] 杨雄文, 杨永强, 刘洋, 等. 激光选区熔化成型典型几何特征尺寸精度研究[J]. 中国激光, 2015, 42(3): 0303004.

Yang Xiongwen, Yang Yongqiang, Liu Yang, et al.. Study on dimensional accuracy of typical geometric features manufactured by selective laser melting[J]. Chinese J Lasers, 2015, 42(3): 0303004.

[12] 王续跃, 王彦飞, 江豪, 等. 圆形倾斜薄壁件的激光熔覆成形[J]. 中国激光, 2014, 42(1): 0103006.

Wang Xuyue, Wang Yanfei, Jiang Hao, et al.. Laser cladding forming of round thin-walled parts with slope angle[J]. Chinese J Lasers, 2014, 42(1): 0103006.

[13] 穆存远, 刘孟林, 李楠. 快速成型中的台阶负偏差及其降低措施[J]. 沈阳建筑大学学报(自然科学版), 2011, 27(2): 361-366.

Mu Cunyuan, Liu Menglin, Li Nan. The negative step deviation in rapid prototyping and its reduction measurements[J]. Journal of Shenyang Jianzhu University (Natural Science), 2011, 27(2): 361-366.

[14] Strano G, Hao L, Everson R M, et al.. Surface roughness analysis, modeling and prediction in selective laser melting[J]. Journal of Materials Processing Technology, 2013, 213(4): 589-597.

[15] Yan C, Hao L, Hussein A, et al.. Advanced lightweight 316L stainless steel cellular lattice structures fabricated via selective laser melting [J]. Materials and Design, 2014, 55: 533-541.

[16] 赵进炎, 仇毅, 刘富荣, 等. SLM 成型医用钴铬合金的表面粗糙度与致密度研究[J]. 应用激光, 2014, 34(6): 524-527.

Zhao Jinyan, Chou Yi, Liu Furong, et al.. Research of surface roughness and relative density of SLM medical Co-Cr alloy[J]. Applied Laser, 2014, 34(6): 524-527.

[17] 卢建斌, 杨永强, 王迪, 等. 选区激光熔化成型悬垂面质量的影响因素分析[J]. 激光技术, 2011, 35(2): 148-151.

Lu Jianbin, Yang Yongqiang, Wang Di, et al.. Analysis of affecting factors of overhanging surface quality by selective laser melting[J]. Laser Technology, 2011, 35(2): 148-151.

[18] 刘睿诚. 激光选区熔化成型零件表面粗糙度研究及在免组装机构中的应用[D]. 广州: 华南理工大学, 2014: 36-39.

Liu Ruicheng. The Study on Surface Roughness of Metal Parts Fabricated by Selective Laser Melting and the Application on Non-assembly Mechanisms[D]. Guangzhou: South China University of Technology, 2014: 36-39.

[19] 卢建斌. 个性化精密金属零件选区激光熔化直接成型设计优化及工艺研究[D]. 广州: 华南理工大学, 2011: 26-27.

Lu Jianbin. Design Optimization and Process Study on Directly Manufacturing of Customized Precise Metal Parts by Selective Laser Melting [D]. Guangzhou: South China University of Technology, 2011: 26-27.

[20] Gebhardt A, Hotter J S, Ziebura D. Impact of SLM build parameters on the surface quality[J]. Rapid Technologie Journal, 2014.

[21] 孙婷婷, 杨永强, 郭明华. 选区激光熔化316L不锈钢粉末形貌分析[J]. 激光杂志, 2009, 30(5): 68-70.

Sun Tingting, Yang Yongqiang, Guo Minghua. Analysis of the morphology of 316L stainless part formed by selective laser melting[J]. Laser Journal, 2009, 30(5): 68-70.

麦淑珍, 杨永强, 王迪. 激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究[J]. 中国激光, 2015, 42(12): 1203004. Mai Shuzhen, Yang Yongqiang, Wang Di. Study on Surface Morphology and Roughness Variation of NiCr Alloy Curved Surface Manufactured by Selective Laser Melting[J]. Chinese Journal of Lasers, 2015, 42(12): 1203004.

激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究下载： 802次

关于本站 Cookie 的使用提示

全站搜索

激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究 下载： 802次

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索

激光选区熔化成型NiCr 合金曲面表面形貌及粗糙度变化规律研究下载： 802次