基于轨迹变换法降低激光切割尖角“烧蚀率”研究

针对常规的氧助激光切割带有尖角(≤30°)图形的中低碳钢板材过程中存在的尖角“烧蚀率”很高的问题，采用Rofin DC025板条CO2激光切割机系统，在优化的激光切割工艺参数的条件下，通过轨迹变换的方法，在3 mm厚的A3钢板上切割出多种带有尖角(≤30°)图形。系统研究了激光切割尖角图形的切割轨迹及参数对尖角“烧蚀率”的影响。结果表明，采用圆心在所切割尖角角平分线上，且通过该尖角顶点的圆形切割轨迹可大大降低激光切割尖角“烧蚀率”。且对于不同尖角大小(≤30°)该轨迹圆都存在一个最优补偿半径可把尖角“烧蚀率”控制在10%以内，获得理想的切割效果。

Abstract

Aiming at the problem of high apex angle burnt rate during laser cutting graphics with apex angle (≤30°) on mild or low carbon steel, the laser cutting experiments have been done on A3 steel board with the thickness of 3 mm by using Rofin DC025 slab CO2 laser cutting system and the method of path transformation. At the same time, the key effects of temperature on apex angle burnt have been analyzed, and the influences of path transformation and its radius on apex angle burnt rate have been studied. The results show that the apex angle burnt rate has been greatly reduced under the condition of a special cutting path, which is a circle passing through the zenith of the apex angle and its centre locating on angle bisector. Meanwhile, the apex angle burnt rate can be controlled lower than 10% under the condition of a optimal circle radius for various apex angle.

参考文献

[1] 刘东华. 激光切割［J］. 激光杂志, 1992, 13(4): 207～213

Liu Donghua. Laser cutting［J］. Laser Journal, 1992, 13(4): 207～213

[2] 李祥友, 曾晓雁, 黄维玲. 激光精密加工技术的现状和展望［J］. 激光杂志, 2000, 21(5): 1～3

Li Xiangyou, Zeng Xiaoyan, Huang Weiling. Status and prospect of precision laser machining［J］. Laser Journal, 2000, 21(5): 1～3

[3] 杨逸民. 脉冲NdYAG激光在精密加工中的应用［J］. 激光与红外, 1997, 27(6): 333～336

Yang Yimin. Applications of precision machining with Nd∶YAG laser［J］. Lasers and Infrared, 1997, 27(6): 333～336

[4] 李祥友, 曾晓雁, 刘勇等. 激光精密切割不锈钢薄板的工艺研究［J］. 中国激光, 2001, 28(12): 1125～1129

Li Xiangyou, Zeng Xiaoyan, Liu Yong et al.. Study of YAG laser cutting process with stainless steel sheet［J］. Chinese J. Lasers, 2001, 28(12): 1125～1129

[5] 李又生. 深孔激光加工研究［J］. 激光技术, 1998, 22(2): 36～40

Li Yousheng. Study on laser deep hole drilling［J］. Laser Technology, 1998, 22(2): 36～40

[6] N. Rajaram, J. Sheikh-Ahmad, S. H. Ceraghi. CO2 laser cut quality of 4130 steel［J］. International Journal of Machine Tools and Manufacture, 2003, 43(4): 351～358

[7] 李淑玉, 田新国, 贺敬地等. 自动流量平衡阀过流曲线激光切割工艺［J］. 中国激光, 2011, 38(10): 1003008

Li Shuyu, Tian Xinguo, He Jingdi et al.. Laser cutting flow curve of automatic flow control valves［J］. Chinese J. Lasers, 2011, 38(10): 1003008

[8] 朱虎, 扶建辉, 刘志军. 基于STL模型的五轴激光切割轨迹生成［J］. 中国激光, 2010, 37(3): 863～867

Zhu Hu, Fu Jianhui, Liu Zhijun. Generation of 5-axis laser cutting path based on STL model［J］. Chinese J. Lasers, 2010, 37(3): 863～867

[9] 党东显, 盛晓军, 胡俊等. 喷嘴工件距对激光切缝中气体流场的影响［J］. 中国激光, 2010, 37(10): 2625～2631

Dang Dongxian, Sheng Xiaojun, Hu Jun et al.. Effect of standoff distance on flow field of assist gas in cutting slot in laser cutting［J］. Chinese J. Lasers, 2010, 37(10): 2625～2631

[10] 郑启光. 激光先进制造技术［M］. 武汉: 华中科技大学出版社, 2002. 25～27

Zheng Qiguang. Laser Advanced Manufacture［M］. Wuhan: Press of Huazhong University of Science and Technology, 2002. 25～27

[11] 梁耀荣. 激光加工温度与激光功率及加工速度关系的研究［J］. 航空精密制造技术, 1996, 32(6): 17～19

Liang Yaorong. Study of correlation between material surface temperature and laser average power and cutting speed［J］. Aviation Precision Manufacturing Technology, 1996, 32(6): 17～19

[12] S. L. Chen, W. M. Steen. The theoretical investigation of gas assisted laser cutting［C］. SPIE, 1992, 1722: 221～230

[13] H. Kaebernick, A. Jeromin, P. Mathew. Adaptive control for laser cutting using frequency analysis［J］. Annals of the CIRP, 1998, 47(1): 137～140

[14] H. Cheng, W. O′Neill. The effects of power rippling on CO2 laser cutting［J］. Opt. Technology, 1997, 29(3): 125～134

[15] W. O′Neill, W. M. Steen. A three dimensional analysis of gas entrainment operating during the laser cutting process［J］. J. Phys. D, 1995, 28(1): 12～18

[16] A. Kratky, D. Schuocker, G. Liedl. Processing with kW fiber lasers-advantages and limits［C］. SPIE, 2009, 7131: 71311X

邓前松, 赵辰丰, 陈亮, 石明国, 杨卫红, 唐霞辉. 基于轨迹变换法降低激光切割尖角“烧蚀率”研究[J]. 中国激光, 2012, 39(8): 0803006. Deng Qiansong, Zhao Chenfeng, Chen Liang, Shi Mingguo, Yang Weihong, Tang Xiahui. Study on Reducing Apex Angle Burnt Rate during Laser Cutting Based on Path Transformation[J]. Chinese Journal of Lasers, 2012, 39(8): 0803006.

基于轨迹变换法降低激光切割尖角“烧蚀率”研究

关于本站 Cookie 的使用提示

全站搜索

基于轨迹变换法降低激光切割尖角“烧蚀率”研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索