工件形状对镍基高温合金激光再制造应力场分布的影响

王凯; 赵剑峰; 潘浒; 刘云雷

doi:doi:10.3788/lop50.041402

激光与光电子学进展, 2013, 50 (4): 041402, 网络出版: 2013-03-22

工件形状对镍基高温合金激光再制造应力场分布的影响

Influence of Repair Cross Section on Stress-Field Distribution in the Nickel-Based Superalloy Laser Remanufacturing

论文大纲

王凯 ^*赵剑峰潘浒刘云雷

作者单位

南京航空航天大学机电学院, 江苏南京 210016

激光技术再制造残余应力有限元方法激光熔覆 laser technique remanufacturing residual stress finite element method laser cladding

摘要

利用Marc软件对基于同轴送粉的镍基高温合金GH4169零件表面修复过程进行了数值模拟，通过热机直接耦合分析了不同的修复截面形状对激光熔覆过程中温度场/残余应力场的分布的影响。结果表明，对于单道的激光表面修复，修复截面形状的不同将导致在结合面处的温度场/残余应力场的分布也呈现出不同的特点：直接在平面上修复时，残余应力平行于扫描路径上的分量明显大于其垂直分量；在修复截面为矩形或弧形凹坑时，由于熔覆材料受到凹坑两侧面的约束作用，残余应力垂直于扫描方向的分量相对于平面上直接修复时明显增加，且随着深宽比的增加，垂直分量对平行分量的比值也有进一步增大的趋势，但在同深宽比情况下，弧形凹坑的比值较小。为避免薄壁零件的变形，预处理时宜采用深宽比较小的弧形修复截面。

Abstract

A numerical simulation of laser cladding process on the surface of nickel-based superalloy GH4169 with coaxial powder feeding system is carried out by Marc software. The influence of different repair cross sections on the distribution of temperature and residual stress field is studied through a directly coupled thermo-mechanical analysis. The results show that for single-path laser surface reparation, different repair cross sections lead to different distribution characteristics of temperature and residual stress field in the bonding zone. The parallel component of residual stress is evidently larger than vertical component in the direction of the scanning path when it is repairing on a plane. The vertical component of residual stress is relatively increased due to the constraints from two sides of the crater when it is repairing a crater of a long strip with rectangular or arc-shaped cross section. As the aspect ratio of the section increases, the ratio of vertical component of residual stress to parallel component also increases. However, the ratio of vertical component of residual stress to parallel component for arc-shaped cross section is smaller for the same aspect ratio. In order to avoid the deformation of the thin-walled parts, an arc-shaped cross section with small aspect ratio is recommended.

参考文献

[1] 宋兆泓. 航空发动机可靠性与故障抑制工程[M]. 北京: 北京航空航天大学出版社, 2002. 10～13

Song Zhaohong. Aero-Engine Reliability and Fault Control Engineering [M]. Beijing: BUAA Press, 2002. 10～13

[2] 张晓东, 董世运, 徐滨士等. 激光熔覆再制造成形金属裂纹的控制措施[C]. 第四届世界维修大会, 2008

Zhang Xiaodong, Dong Shiyun, Xu Binshi et al.. Control measure for metal cracks of laser cladding remanufacturing [C]. The 4th World Congress on Maintenance, 2008

[3] E. Brtlcker, D. Lepski, E. Beyer. Modeling the influence of process parameters and additional heat sources on residual stresses in laser cladding [J]. J. Thermal Spray Technol., 2007, 16(3): 355～373

[4] G. Palumbo, S. Pinto, L. Tricarico. Numerical finite element investigation on laser cladding treatment of ring geometries [J]. J. Mater. Process. Technol., 2004, 155-156: 1443～1450

[5] 李守卫, 沈以赴, 顾冬冬等. 多组元金属粉末激光选区烧结热力耦合有限元应力场分析[J]. 中国机械工程, 2007, 18(6): 751～755

Li Shouwei, Shen Yifu, Gu Dongdong et al.. Thermal-mechanical coupling finite element analysis of stress field in selective laser sintering of multi-component metal powder [J]. China Mechanical Engineering, 2007, 18(6): 751～755

[6] 程广萍, 李明喜, 何宜柱等. 激光熔覆层温度场和应力场的数值模拟[J]. 热处理, 2009, 24(4): 49～53

Cheng Guangping, Li Mingxi, He Yizhu et al.. Numerical simulation of temperature field and stress field in laser clad coating [J]. Heat Treatment, 2009, 24(4): 49～53

[7] 李俐群, 张亮, 戴景明. 激光填丝多层焊温度场和应力场的数值模拟[J]. 中国激光, 2011, 38(10): 1003002

Li Liqun, Zhang Liang, Dai Jingming. Numerical simulation of temperature and stress fields in wire filling laser multilayer welding [J]. Chinese J. Lasers, 2011, 38(10): 1003002

[8] 占焕校, 王勇, 韩涛等. 42CrMo钢表面单道激光宽带处理后熔凝层的残余应力[J]. 中国激光, 2008, 35(4): 625～630

Zhan Huanxiao, Wang Yong, Han Tao et al.. Residual stress analysis of the remelting zone on 42CrMo steel plate in single-pass laser wide-band treatment [J]. Chinese J. Lasers, 2008, 35(4): 625～630

[9] 顾建强, 骆芳, 姚建华. 激光熔覆过程残余应力的数值模拟[J]. 激光与光电子学进展, 2010, 47(10): 101401

Gu Jianqiang, Luo Fang, Yao Jianhua. Numerical simulation of residual stress during laser cladding [J]. Laser & Optoelectronics Progress, 2010, 47(10): 101401

[10] 陈明祥. 弹塑性力学[M]. 北京：科学出版社, 2010. 123～131

Cheng Mingxiang. Elasticity and Plasticity [M]. Beijing: Science Press, 2010. 123～131

[11] 中国航空材料手册编辑委员会. 中国航空材料手册(第2版)[M]. 北京: 中国标准出版社, 2002

China Aeronautical Materials Handbook Editorial Committee. China Aeronautical Materials Handbook (2nd ed.) [M]. Beijing: China Standard Press, 2002

[12] Y. S. Touloukian. Thermophysical Properties of Matter [M]. New York: IFI/Plenum,1970. 263

王凯, 赵剑峰, 潘浒, 刘云雷. 工件形状对镍基高温合金激光再制造应力场分布的影响[J]. 激光与光电子学进展, 2013, 50(4): 041402. Wang Kai, Zhao Jianfeng, Pan Hu, Liu Yunlei. Influence of Repair Cross Section on Stress-Field Distribution in the Nickel-Based Superalloy Laser Remanufacturing[J]. Laser & Optoelectronics Progress, 2013, 50(4): 041402.

工件形状对镍基高温合金激光再制造应力场分布的影响

关于本站 Cookie 的使用提示

全站搜索

工件形状对镍基高温合金激光再制造应力场分布的影响

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索