CO<sub>2</sub>激光刻蚀PMMA制备微流道的研究

李晓宇; 陈继民; 刘富荣; 李晓刚; 张强

doi:doi:10.3788/lop48.041401

激光与光电子学进展, 2011, 48 (4): 041401, 网络出版: 2011-03-24

CO₂激光刻蚀PMMA制备微流道的研究

Micro-Channel Fabrication with CO2 Laser Ablation of Polymethyl Methacrylate

论文大纲

李晓宇 ^*陈继民刘富荣李晓刚张强

作者单位

北京工业大学激光工程研究院, 北京 100124

激光刻蚀聚甲基丙烯酸甲脂 CO2激光微流道深度模型 laser ablation polymethyl methacrylate CO2 laser micro channel depth model

摘要

介绍了采用CO2激光器对聚甲基丙烯酸甲脂(PMMA)板进行刻蚀制备微流道的工艺实验。通过实验分析工艺参数对微流道深度和宽度的影响及其中变化规律。结果表明，激光线能量密度与刻蚀微流道宽度两者关系呈指数增长，得到了线能量密度和微流道宽度的数学拟合公式，曲线和数据点拟合决定系数R2=0.96。当线能量密度小于300 J/m时，微流道深度与线能量密度呈近似线性关系；当线能量密度大于300 J/m时，偏离线性关系。通过理论计算得到在低线能量密度下微流道深度的变化曲线图，并与实际测量值吻合较好。最后，通过优化工艺参数，制备出微流道宽度为170 μm，深度为180 μm的生物芯片。

Abstract

A micro-ablation of polymethyl methacrylate (PMMA) is carried out by CO2 laser. The effect of the process parameters on the depth and width of the channel is further studied. The rule of the process parameters how to affect the groove depth and width is obtained by the experimental analysis. The results show that the laser line energy density has an exponential relation with the channel width. Through the experiment, we achieve the experiental formula about the line energy density and groove width and the decisive coefficient R2 is 0.96. When the line energy density is less than 300 J/m, the depth of ablated channel has a linearity relation with the line energy density, but this relation is deviated for the line energy density over 300 J/m. By the law of conservation of energy, a model about the channel depth and line energy density is set up. At the situation of low line energy density less than 300 J/m, the calculated results agree well with the experiment. At last, with optimization of process parameters, we make a fine biochip with width of 170 μm and depth of 180 μm.

参考文献

[1] 王宏杰, 郭文刚, 董兆辉等. 激光刻蚀技术的应用［J］. 红外与激光工程, 2004, 33(5): 469～472

Wang Hongjie, Guo Wengang, Dong Zhaohui et al.. Application of laser etching technology［J］. Infrared and Laser Engineering, 2004, 33(5): 469～472

[2] 赵泽宇, 侯德胜, 董小春等. 准分子激光刻蚀聚碳酸酯材料研究［J］. 光电工程, 2004, 31(2): 4～7

Zhao Zeyu, Hou Desheng, Dong Xiaochun et al.. Research on etching properties of polycarbonate by KrF excimer laser［J］. Opto-Electronic Engineering, 2004, 31(2): 4～7

[3] 章琳, 楼棋洪, 魏运荣等. 准分子激光刻蚀聚合物微图形制作研究［J］. 激光技术, 2002, 126(2): 94～96

Zhang Lin, Lou Qihong, Wei Yunrang et al.. Micropatterns on polymers etched by excimer lasers［J］. Laser Technology, 2002, 126(2): 94～96

[4] Hong Tingfu, Zhu Weizhong, Liang Zhichuang et al.. Rapid fabrication of microfluidic chip on PMMA substrate by CO2 laser \[J\]. Nanotechnology and Precision Engineering, 2009, 7(4): 352～354

[5] . P. Kutter, O. Geschke. CO2-laser micromachining and back-end processing for rapid production of PMMA-based microfluidic systems[J]. Lab. Chip., 2002, 2(4): 242-246.

[6] . Kutter. Microstructure fabrication with a CO2 laser system[J]. J. Micromech. Microeng., 2004, 14(2): 182-189.

[7] . Romoli, G. Tantussi, G. Dini. Layered laser vaporization of PMMA manufacturing 3D mould cavities[J]. Annals of the CIRP, 2007, 56(1): 209-212.

[8] . . Laser patterning and packaging of CCD-CE-Chips made of PMMA[J]. Sensor. Actuat. B-Chem., 2009, 138(1): 336-343.

[9] 祁恒, 王松贤, 陈涛等. PMMA基连续流PCR微流控芯片的CO2激光直写加工与应用［J］. 中国激光, 2009, 36(5): 1239～1245

Qi Heng, Wang Songxian, Chen Tao et al.. Fabrication and application of PMMA continuous-flow PCR microfluidic chip with CO2 laser direct-writing ablation micromaching technique［J］. Chinese J. Lasers, 2009, 36(5): 1239～1245

[10] . 三维瞬态激光烧蚀聚合物微流道动态界面研究[J]. 浙江大学学报(工学版), 2007, 41(11): 1908-1911.

. Dynamic interface for three-dimensional transient laser ablation polymer micro-channels[J]. J. Zhejiang University (Engineering Science), 2007, 41(11): 1908-1911.

[11] 茆诗松, 程依明, 濮晓龙. 概率论与数理统计［M］. 北京：高等教育出版社, 2008. 418～419

Mao Shisong, Cheng Yiming, Pu Xiaolong. Probability and Statistics Tutorial［M］. Beijing: Higher Education Press, 2008. 418～419

[12] . . Surface roughness analysis and improvement of PMMA-based microfluidic chip chabers by CO2 laser cutting[J]. Appl. Surf. Sci., 2010, 256(6): 1675-1678.

[13] 左铁钏. 21世纪的先进制造激光技术与工程［M］. 北京：科学出版社, 2007. 13～14

Zuo Tiechuang. The 21st Century′s Advanced Manufacturing-Laser Technology and Engineering［M］. Beijing: Science Press, 2007. 13～14

[14] M. G. Baeva. CW CO2 laser cutting of plastics［C］. SPIE, 1997, 3092: 772～775

[15] S. Turchetta, L. Carrino. An energy based model for laser cutting natural stone［J］. Int. J. Mach. Tool. Manu., 2005, 45(7-8): 761～767

[16] . Arisawa, T. B. Brill. Kinetics and mechanisms of flash pyrolysis of poly (methyl methacrylate) (PMMA)[J]. Combust and Flame, 1997, 109(3): 415-426.

李晓宇, 陈继民, 刘富荣, 李晓刚, 张强. CO₂激光刻蚀PMMA制备微流道的研究[J]. 激光与光电子学进展, 2011, 48(4): 041401. Li Xiaoyu, Cheng Jimin, Liu Furong, Li Xiaogang, Zhang Qiang. Micro-Channel Fabrication with CO2 Laser Ablation of Polymethyl Methacrylate[J]. Laser & Optoelectronics Progress, 2011, 48(4): 041401.

CO₂激光刻蚀PMMA制备微流道的研究

关于本站 Cookie 的使用提示

全站搜索

CO2激光刻蚀PMMA制备微流道的研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索

CO₂激光刻蚀PMMA制备微流道的研究