基于改进三点测量法的圆径测量研究

三点测量圆度误差分离技术被广泛应用于工件形状的圆度误差和电机旋转的回转误差的分离算法中。而圆度误差能得以准确分离的关键在于合理配置三个位移传感器测头的安装角度, 从而避免传递函数的分母为零的情况出现。然而, 在具体实施过程中, 位移传感器测头的角度安装误差是必然存在的, 这就使得分析这一角度安装误差带来的影响变得尤为重要。基于经典的三点测量法模型, 提出一种新的分析位移传感器测头的角度安装误差的模型。以三点测量法圆度测量中的圆径结果为目标, 根据实际工况下的各种参数设置, 定量分析了位移传感器测头的角度安装误差对最终结果的影响程度。最后, 使用电容位移传感器开展工件外圆的圆径测量实验研究, 确认了文中误差分析的有效性, 圆径测量的重复性精度可以达到2 滋m以下。

Abstract

The roundness error separation technique of three-point method was widely used in the separation algorithm for roundness error of part shapes and rotation error of motors. The key of accurate separation in roundness error depended on setting the angles of three displacement sensor probes logically, in order to avoid that the denominator of transfer function became zero. However, during the process of specific implementation, the angle setting error of displacement sensor probes inevitably existed, which made analyzing the influence of angle setting error become much more important. Based on the classical model of three-point method, and then a new model was presented for analyzing the angle setting error of displacement sensor probes. Taking the diameter results in measuring roundness through three-point method as the goal, according to different parameter settings in actual working situations, the error of measuring results caused by the angle setting error of displacement sensor probes was quantitatively analyzed. Lastly, using capacitive displacement sensor to carry out the research on measuring diameter of circular parts, the effectiveness of error analysis was confirmed in this article and the repeatability accuracy of measuring diameter which can be less than 2 滋m.

参考文献

[1] Aoki Yasuo, Ozono Shigeo. On a new method of roundness measurement based on the three-point method [J]. Journal of the Japan Society of Precision Engineering, 1966, 32(12): 27-32.

[2] Ma Yuzhen, Wang Xinhua, Kang Yanhui, et al. Roundness measurement and error separation technique [J]. Applied Mechanics and Materials, 2013, 303-306: 390-393.

[3] Whitehouse D J. Some theoretical aspects of error separation technique in surface metrology [J]. Journal of Physics E Scientific Instruments, 1976, 9(7): 531-536.

[4] Gao Wei, Kiyono Satoshi. High-accuracy roundness measurement by a new error separation method [J]. Precision Engineering, 1997, 21(2-3): 123-133.

[5] 洪迈生, 邓宗煌, 陈健强, 等. 精确的时域三点测量法圆度误差分离技术[J]. 上海交通大学学报, 2000, 34(10): 1317-1319.

Hong Maisheng, Deng Zhonghuang, Chen Jianqiang, et al. Accurate time domain three point method for error separation of roundness[J]. Journal of Shanghai Jiaotong University, 2000, 34(10): 1317-1319. (in Chinese)

[6] Lei Xianqing, Zhang Chunyang, Xue Yujun, et al. Roundness error evaluation algorithm based on polar coordinate transform [J]. Measurement, 2011, 44(2): 345-350.

[7] Muralikrishnan B, Venkatachalam S, Raja J, et al. A note on the three-point method for roundness measurement[J]. Precision Engineering, 2005, 29(2): 257-260.

[8] 洪迈生, 魏元雷, 苏恒, 等. 三平行传感器式频域法误差分离技术——在线测量圆度误差的新方法[J]. 仪器仪表学报, 2003, 24(2): 152-156.

Hong Maisheng, Wei Yuanlei, Su Heng, et al. A new method for on-machine measurement of roundness - error separation technique of parallel three-probe method in frequency domain[J]. Chinese Journal of Science Instrument, 2003, 24(2): 152-156. (in Chinese)

[9] GB/T 4380-2004, Assessment of departure from roundness-Two-and three-point methods[S]. 2005-07-01. (in Chinese)

[10] 刘杰, 李华, 付西红. 大尺寸筒状设备圆度误差测量系统[J]. 红外与激光工程, 2016, 45(1): 0117005.

Liu Jie, Li Hua, Fu Xihong. Measurement system of large-scale sleeve roundness error[J]. Infrared and Laser Engineering, 2016,45(1): 0117005. (in Chinese)

[11] Yang T, Wang Z, Wu Z, et al. Calibration of laser beam direction for inner diameter measuring device[J]. Sensors, 2017, 17(2): 0294.

[12] 李超, 申力, 施斐斐. 同轴空心激光检测圆柱内孔圆度误差的方法研究[J]. 红外与激光工程, 2018, 47(S1): S106001.

Li Chao, Shen Li, Shi Feifei. Research on the method of detecting the roundness error of cylindrical inner-hole by using coaxial hollow laser[J]. Infrared and Laser Engineering, 2018, 47(S1): S106001. (in Chinese)

, , , , . 基于改进三点测量法的圆径测量研究[J]. 红外与激光工程, 2019, 48(5): 0517008. Zhong Yilin, Wu Enqi, Cai Xiaoyu, Wei Jiasi, Lei Lihua. Diameter measurement based on improved three-point method[J]. Infrared and Laser Engineering, 2019, 48(5): 0517008.

基于改进三点测量法的圆径测量研究

关于本站 Cookie 的使用提示

全站搜索

基于改进三点测量法的圆径测量研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索