激光熔覆镍基合金涂层微观组织研究

袁庆龙; 冯旭东; 曹晶晶; 苏志俊

doi:doi:10.3788/cjl20103708.2116

中国激光, 2010, 37 (8): 2116, 网络出版: 2010-08-13

激光熔覆镍基合金涂层微观组织研究

Yuan Qinglong,Feng Xudong,Cao Jingjing,Su Zhijun

论文大纲

袁庆龙 ^*冯旭东曹晶晶苏志俊

作者单位

河南理工大学材料科学与工程学院,河南焦作 454000

激光技术激光熔覆镍基合金组织形貌成分分布硬度 laser technique laser cladding Ni-based alloy morphology component distribution hardness

摘要

利用CO2激光在Q235低碳钢表面激光熔覆制备Ni60合金。分别用扫描电镜、能谱分析、显微硬度计对熔覆层的微观组织、成分分布、显微硬度进行了测定与分析。结果表明,激光熔覆Ni60涂层组织为典型的快速凝固组织。熔覆层底部为垂直于界面生长的胞状结构,中部为树枝状结构且晶粒生长具有单一方向性,顶部也为枝状结构,其晶粒生长呈多向性。枝晶间存在着大量的共晶化合物,黑色区域内含有大量的合金渗碳体等金属间化合物。通过固溶强化、弥散强化、硬质相强化以及细晶强化作用,熔覆层的显微硬度明显高于基材,达到了强化表面的目的。

Abstract

Ni60 alloy coatings are prepared on the soft steel (Q235) surface by using a CO2 laser. Cross-section microstructure characteristics of the coating are studied by using scanning electronic microscope,energy spectrum,and micro-hardness analysis. The results show that the microstructure of Ni60 coating by laser cladding is typical rapid solidification structure. The morphology at the bottom of the cladding layer is a cell structure,whose growth is perpendicular to the interface of cladding and substrate. The morphology at the central and top zones of the layer is dendritic structure. The crystal grain of central zone grows with a single direction,but that of the surface layer grows with random direction. There are a large number of eutectic compounds at the middle of the dendrite. The black area contains a large number of inter-metallic compounds,such as alloy cementite. With the effects of solid solution strengthening,dispersion strengthening,hard phase strengthening,and fine grain strengthening,the hardness of the cladding layer is obviously greater than that of the substrate,which achieves the goal of hardening surface.

参考文献

[1] . Uenishi,K. F. Kobayashi. Formation of surface layer based on Al3Ti on aluminum by laser cladding and its compatibility with ceramics[J]. Intermetallics, 1999, 7(5): 553-559.

[2] 陈永哲,王存山,李婷等. 镁合金表面激光熔覆Ni-Zr-Al合金涂层成分设计与组织性能[J]. 中国激光,2009,36(8):2187-2191

Chen Yongzhe,Wang Cunshan,Li Ting et al.. Composition design and properties of laser clad Ni-Zr-Al alloy coating on the magnesium surface[J]. Chinese J. Lasers,2009,36(8):2187-2191

[3] G. Y. Liang,T. T. Wong,J. M. K. MacAlpine et al.. A study of wear resisance of plasma-sprayed and laser-remelted coatings on aluminium alloy[J]. Surface & Coatings Technology,2000,127(2-3):233-238

[4] 刘秀波,石世宏,傅戈雁等. γ-TiAl合金Ni-Cr-C-CaF2复合材料激光熔覆[J]. 中国激光,2009,36(6):1591-1594

Liu Xiubo,Shi Shihong,Fu Geyan et al.. Ni-Cr-C-CaF2 composite laser cladding on γ-TiAl intermetallic alloy[J]. Chinese J. Lasers,2009,36(6):1591-1594

[5] . Puri,S. Prakash. Mechanical and metallurgical properties of plasma sprayed and laser remelted Ni-20Cr and Stellite-6 coatings[J]. Jourmal of Meterials Processing Technology, 2005, 159(3): 347-355.

[6] Xie Guozhi,Zhang Jingxian,Liu Yijun et al.. Effect of laser remelting on corrosion behavior of plasma-sprayed Ni-coated WC coatings[J]. Materials Science and Engineering A,2007,460-461:351-356

[7] . A study of Ni-based WC composite coatings by laser induction hybrid rapid cladding with elliptical spot[J]. Applied Surface Science, 2008, 254(10): 3110-3119.

[8] T. Gomez-del Rio,M. A. Garrido,J. E. Fernandez et al.. Influence of the deposition techniques on the mechanical properties and microstructure of NiCrBSi coatings[J]. Journal of Meterials Processing Technology,2008,204(1-3):304-312

[9] . Partes,C. Giolli,F. Borgioli et al.. High temperature behaviour NiCrAlY coatings made by laser cladding[J]. Surface & Coatings Technology, 2008, 202(10): 2208-2213.

[10] 董江,陈岁元,刘大亮等. 铜合金表面激光原位制备钴基合金涂层的结构与机制[J]. 中国激光,2009,36(5):1302-1307

Dong Jiang,Chen Suiyuan,Liu Daliang et al.. Structure and mechanism of Co-based alloy coating with laser inducing in-situ synthesis on the surface of copper alloy[J]. Chinese J. Lasers,2009,36(5):1302-1307

[11] . Nurminen,J. Nakki,P. Vuoristo. Microstructure and properties of hard and wear resistant MMC coatings deposited by laser cladding[J]. Journal of Refractory Metals & Hard Meterials, 2009, 27(2): 472-478.

[12] 何宜柱,斯松华,徐锟等. Cr3C2对激光熔覆钴基合金涂层组织与性能的影响[J]. 中国激光,2004,31(9):1143-1148

He Yizhu,Si Songhua,Xu Kun et al.. Effect of Cr3C2 particles on microstructure and corrosion-wear resistance of laser cladding Co-based alloy coating[J]. Chinese J. Lasers,2004,31(9):1143-1148

[13] . 钛合金表面激光熔覆镍铬硅复合涂层的显微组织和摩擦学性能[J]. 机械工程材料, 2008, 32(7): 52-55.

. Microstructure and tribological property of laser cladding Ni-Cr-Si composite coatings on titanium alloy[J]. Materials for Mechanical Engineering, 2008, 32(7): 52-55.

[14] . 镍基合金涂层炉内重熔研究[J]. 太原理工大学学报, 2000, 31(1): 27-30.

. Research on remelting furnace of Ni-based alloy coatings[J]. Journal of Taiyuan University of Technology, 2000, 31(1): 27-30.

[15] 孙耀宁. 激光熔覆TiC增强Ti基复合涂层的组织与性能[J]. 应用激光,2008,28(4):282-286

Sun Yaoning. Microstructures and properties of laser clad TiC reinforced Ti matrix composite coatings[J]. Applied Laser,2008,28(4):282-286

袁庆龙, 冯旭东, 曹晶晶, 苏志俊. 激光熔覆镍基合金涂层微观组织研究[J]. 中国激光, 2010, 37(8): 2116. Yuan Qinglong, Feng Xudong, Cao Jingjing, Su Zhijun. Yuan Qinglong,Feng Xudong,Cao Jingjing,Su Zhijun[J]. Chinese Journal of Lasers, 2010, 37(8): 2116.

激光熔覆镍基合金涂层微观组织研究

关于本站 Cookie 的使用提示

全站搜索

激光熔覆镍基合金涂层微观组织研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索