钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析

高伟; 阎启; 黄坚

doi:doi:10.3788/cjl201441.0603006

中国激光, 2014, 41 (6): 0603006, 网络出版: 2014-04-09

钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析

Microstructure and Mechanical Property of Laser Wire Fusion Brazing Welded Butt Joints of Steel/Aluminum Dissimilar Metal

论文大纲

高伟 ^1,2,*阎启 ¹黄坚 ^1,2

作者单位

¹ 宝钢集团汽车用钢开发与应用技术国家重点试验室, 上海 201900

² 上海交通大学上海市激光制造与材料改性重点试验室, 上海 200240

摘要

采用光纤激光和铝硅焊丝对2.5 mm厚6013铝合金和镀锌低碳钢的异种金属对接接头进行了激光填丝熔钎焊。采用光学显微镜、扫描电子显微镜（SEM）和能谱仪（EDS）分析了熔钎焊对接接头的微观组织，采用拉伸试验测试了接头强度，并研究了热输入对钢/焊缝界面处金属间化合物和接头强度的影响。试验结果表明，在适当焊接参数下可以获得成形良好和具有一定抗拉强度的钢/铝对接接头。进一步分析表明，钢/焊缝界面处主要生成了FeAl2和FeAl3金属间化合物。随着热输入量的增加，金属间化合物的厚度随之增加。焊缝中的组织则为α-Al基体晶界上均匀分布着条状Al-Si共晶组织。在钢板采用30°坡口时可以获得的最大抗拉强度为88 MPa，采用45°坡口时强度可以达到135 MPa。

Abstract

Dissimilar metal butt joints of 2.5 mm thick 6013 aluminum alloy and galvanized low carbon steel are welded by fiber laser wire fusion brazing method. The microstructure of the fusion brazing welded joints is investigated by optical microscope, scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). The joint strength is measured by tensile test. The effect of heat input on interface intermetallic compounds of aluminum/steel butt joint and joint strength are discussed. Experimental results show that butt joints with good appearance and certain tensile strength can be obtained under appropriate welding parameters. Further analysis reveal that this kinds of intermetallic compounds on the interface are mainly FeAl2 and FeAl3. With the increase of heat input, the thickness of the intermetallic compound is also increased. The uniform distribution of Al-Si eutectic along grain boundaries on α-Al substrate shows in welded seams. The maximum tensile strength of welded joints with a 30° groove is 88 MPa, the strength can reach up to 135 MPa when using a 45° groove.

参考文献

[1] 陈健, 浦娟, 吴铭方, 等. 铝及铝合金与钢连接技术研究进展[J]. 江苏科技大学学报(自然科学版), 2008, 22(2): 39-44.

Chen Jian, Pu Juan, Wu Mingfang, et al.. The study progress on the joining technology of Al and Al alloys to steel[J]. Journal of Jiangsu University of Science and Technology (Natural Science Edition), 2008, 22(2): 39-44.

[2] Rattana Borrisutthekul, Taisei Yachi, Yukio Miyashita, et al.. Suppression of intermetallic reaction layer formation by controlling heat flow in dissimilar joining of steel and aluminum alloy[J]. Materials Science and Engineering: A, 2007, 467(1-2): 108-113.

[3] H Laukant, C Wallmann, M Müller. Fluxless laser beam joining of aluminum with zinc coated steel[J]. Science and Technology of Welding and Joining, 2005,10(2): 219-226.

[4] H Uzun, C D Donne, A Argagnotto, et al.. Friction stir welding of dissimilar Al6013-T4 to X5CrNi18-10 stainless steel[J]. Materials and Design, 2005, 26(1): 41-46.

[5] 崔晴晴. 铝合金和镀锌钢的CMT焊接技术研究[D]. 镇江: 江苏科技大学, 2012.

Cui Qingqing. Study on CMT Welding Technology Between Aluminum Alloy and Galvanized Steel[D]. Zhenjiang: Jiangsu University of Science and Technology, 2012.

[6] 孙建雄, 李亚江, 秦国良, 等. 铝和Q235镀锌钢搭接GMAW熔钎焊接头组织分析[J]. 现代焊接, 2013, (3): 26-28.

Sun Jianxiong, Li Yajiang, Qin Guoliang, et al.. Microstructure analysis of aluminum and Q235 galvanized steel lap GMAW welding-brazing joint[J]. Modern Welding, 2013, (3): 26-28.

[7] G Sierra, P Peyre, F Deschaux-Beaume, et al.. Galvanized steel to aluminum joining by laser and GTAW processes[J]. Material Characterization, 2008, 59(12): 1705-1715.

[8] 张明军, 陈根余, 李时春, 等. 车用铝合金与镀锌钢光纤激光搭接焊试验研究[J]. 中国激光, 2011, 38(6): 134-139.

Zhang Mingjun, Chen Genyu, Li Shichun, et al.. Experimental investigation on fiber laser overlap welding of automotive aluminum to galvanized steel[J]. Chinese J Lasers, 2011, 38(6): 0603010.

[9] 赵旭东, 肖荣诗. 铝/钢异种金属无钎剂激光填粉熔钎焊接[J]. 中国激光, 2012, 39(4): 0403004.

Zhao Xudong, Xiao Rongshi. Fluxless joining between aluminum alloy and galvanized steel by fiber laser fusion welding-brazing with filler powder[J]. Chinese J Lasers, 2012, 39(4): 0403004.

[10] G Sierra, P Peyre, F Deschaux-Beaume, et al.. Steel to aluminum braze welding by laser process with Al-12Si filler wire[J]. Science and Technology of Welding and Joining, 2008, 13(5): 430-437.

[11] 王涛, 周惦武, 彭艳, 等. 钢/铝异种金属预置Si粉的光纤激光焊接[J]. 中国激光, 2012, 39(3): 0303009.

Wang Tao, Zhou Dianwu, Peng Yan, et al.. Steel to aluminum fiber laser butt welding with Si powder pre-filling[J]. Chinese J Lasers, 2012, 39(3): 0303009.

[12] Kobayashi S, Yakou T. Control of intermetallic compound layers at interface between steel and aluminum by diffusion-treatment[J]. Materials Science and Engineering: A, 2002, 338(1): 44-53.

高伟, 阎启, 黄坚. 钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析[J]. 中国激光, 2014, 41(6): 0603006. Gao Wei, Yan Qi, Huang Jian. Microstructure and Mechanical Property of Laser Wire Fusion Brazing Welded Butt Joints of Steel/Aluminum Dissimilar Metal[J]. Chinese Journal of Lasers, 2014, 41(6): 0603006.

钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析

关于本站 Cookie 的使用提示

全站搜索

钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索