新型线性定标的物体光刀切口长度测量研究

吴小平; 余艳梅; 吴晓红; 罗代升

doi:doi:10.3788/lop47.031202

激光与光电子学进展, 2010, 47 (3): 031202, 网络出版: 2010-03-03

新型线性定标的物体光刀切口长度测量研究

Object Cut Length Measurement Using Light-Knife Based on New Linear Calibration

论文大纲

吴小平 ^*余艳梅吴晓红罗代升

作者单位

四川大学电子信息学院图像信息研究所,四川成都 610064

测量光刀切口长度测量激光三角法线性定标光刀 measurement light-knife cut length measurement laser triangulation linear calibration light-knife

摘要

基于激光三角法原理对三维物体光刀切口长度测量做了深入的研究,着重研究了测量原理和定标方法。采用坐标变换方法,分析了三维物体光刀切口长度测量在高度方向上和光刀方向上的物像关系,得出了三维物体光刀切口长度测量的计算公式。基于高度方向和光刀方向的物像关系提出了一种新型线性定标方法。进行了手指长度测量实验,测量结果精度较高。研究结果表明：高度方向上物体相对高度的倒数和像相对高度的倒数成线性关系;光刀方向上物像的长度比和物体的相对高度成线性关系;新的定标方法精度高,操作方便;光刀测量三维物体切口长度精度高、成本低、处理速度快。

Abstract

3D object cut length measurement using light-knife is deeply researched based on laser triangulation,and the measurement principle and calibration method are studied in detail. The object-image relationships in height direction and light-knife direction are analyzed through coordinate transformation method,and the calculation formula of 3D object cut length measurement using light-knife is derived. A new linear calibration method is proposed based on the object-image relationships. An experiment of finger’s length measurement has been done and the results are precise. In the height direction the inverse of object’s relative height is linear with the that of image’s relative height. In the light-knife direction the ratio of object’s length to image’s length is linear with the object’s relative height. The new linear calibration method is very precise and simple. The advantages of 3D object cut length measurement using light-knife are of high accuracy,low cost,and high processing speed.

参考文献

[1] 贺敏,胡以华,赵楠翔等. 机载激光三维成像技术应用现状[J]. 激光与光电子学进展,2008,45(4):43-49

He Min,Hu Yihua,Zhao Nanxiang et al.. Application of airborne three-dimensional laser imaging[J]. Laser & Optoelectronics Progress,2008,45(4):43-49

[2] 陈炳生,刘宝瑛. 棒、线材及螺纹钢截面形状在线测量技术[J]. 激光与光电子学进展,2008,45(2):79-83

Chen Bingsheng,Liu Baoying. On line measure ment of steer,wire,and deformed steel bar cross section[J]. Laser & Optoelectronics Progress,2008,45(2):79-83

[3] 孙宇臣,葛宝臻,张以谟. 物体三维信息测量技术综述[J]. 光电子·激光,2004,15(2):248-254

Sun Yuchen,Ge Baozhen,Zhang Yimo. Review for the 3D information measuring technology[J]. J. Optoelectronics Laser,2004,15(2):0248-0254

[4] 毛先富,苏显渝,陈文静等. 改进傅里叶变换轮廓术的测量算法研究[J]. 光学学报,2008,28(7):1291-1295

Mao Xianfu,Su Xianyu,Chen Wenjing et al.. Analysis on measurement method of improved Fourier transforms profilometry [J]. Acta Optica Sinica,2008,28(7):1291-1295

[5] 欧阳京,吕乃光,吴迪. 基于时间相位展开算法的相位测量轮廓术[J]. 北京机械工业学院学报,2007,22(1):0001-0004

Ouyang Jing,Lü Naiguang,Wu Di. Application of temporal phase unwrapping method in phase measurement profilometry[J]. J. Beijing Ins. Mach.,2007,22(1):0001-0004

[6] 黄红云,张亚锋. 基于调制度的光学三维测量的研究[J]. 光学仪器,2008,30(3):0018-0021

Huang Hongyun,Zhang Yafeng. Study on the optical 3D measurement based on modulation[J]. Opt. Instrum.,2008,30(3):0018-0021

[7] 邵双运,苏显渝,王华等. 调制度测量轮廓术的系统标定[J]. 光学学报,2005,25(2):203-206

Shao Shuangyun,Su Xiangyu,Wang Hua et al.. Calibration of the measurement system based on modulation measurement profilometry[J]. Acta Optica Sinica,2005,25(2):203-206

[8] 王晓嘉,高隽,王磊. 激光三角法综述[J]. 仪器仪表学报,2004,25(增刊):601-604

Wang Xiaojia,Gao Jun,Wang Lei. Survey on the laser triangulation[J]. Chin. J. Sci. Instrument,2004,25(suppl.):601-604

[9] 杨再华,李玉和,李庆祥. 一种基于光学三角法的形貌测量系统[J]. 光学技术,2005,31(4):0622-0623

Yang Zaihua,Li Yuhe,Li Qingxiang et al.. Measuring profile system based on optical rriangular method[J]. Opt. Tech.,2005,31(4):0622-0623

[10] 钟丽云,杨齐民,王翊等. 光学三角法实时测量金属板厚[J]. 激光技术,1998,22(3):136-138

Zhong Liyun,Yang Qimin,Wang Yi et al.. Optical triangle method for real time measuring thickness of metal plate[J]. Laser Technol.,1998,22(3):136-138

[11] . 激光三角法测量的研究[J]. 三明学院学报, 2006, 23(4): 0361-0364.

. Study on laser triangulation method measurement[J]. J. Sanming University, 2006, 23(4): 0361-0364.

[12] 吴剑波,崔振,赵宏等. 光刀中心自适应阈值提取法[J]. 半导体光电,2001,22(1):0062-0064

Wu Jianbo,Cui Zhen,Zhao Hong et al.. An adaptive threshold method for light-knife center acquisition[J]. Semicond. Optoelectronics,2001,22(1):0062-0064

[13] 杨佳,贾书海. 一种新的三维轮廓测量方法[J]. 光子学报,2007,36(6):0972-0975

Yang Jia,Jia Shuhai. A novel method of three dimensional profile measurement[J]. Acta Photonica Sinica,2007,36(6):0972-0975

吴小平, 余艳梅, 吴晓红, 罗代升. 新型线性定标的物体光刀切口长度测量研究[J]. 激光与光电子学进展, 2010, 47(3): 031202. Wu Xiaoping, Yu Yanmei, Wu Xiaohong, Luo Daisheng. Object Cut Length Measurement Using Light-Knife Based on New Linear Calibration[J]. Laser & Optoelectronics Progress, 2010, 47(3): 031202.

新型线性定标的物体光刀切口长度测量研究

关于本站 Cookie 的使用提示

全站搜索

新型线性定标的物体光刀切口长度测量研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索