伺服系统中滚珠丝杠的温度场模型

分析了伺服系统中丝杠螺母的热特性规律，对丝杠温度场进行了简化建模，以快速准确地预测丝杠温度分布及变化。简化模型能较好地预测丝杠温升过程，但稳态误差较大；通过引进时间修正系数修正了该简化模型，修正后的模型能较好地预测丝杠的稳态温度，但对温度上升过程的预测误差较大；鉴于两个模型的特点，基于分段建模的思想，建立了丝杠温度场分段模型，并辨识了模型参数。实验结果表明，不同单热源实验条件下，预测温度误差值在0.5 ℃以内；双热源实验条件下，预测温度误差值在0.8 ℃以内；显示该模型能较好地预测丝杠温度随时间的变化。

Abstract

The thermal characteristics of ball screws in servo systems were analyzed,then a simplificated temperature filed model was established to predict the temperature distribution and variations of the ball screws quickly and accurately. The simplified model can predict the unsteady temperature rising of the ball screws, however, there are big errors when the model was used to predict the steady temperature variations of the ball screws. A new simplified model was built by introducing the factor of time modification in the simplified model. The new model has a good performance in predicting the process of steady temperature, however, there exist big errors when the new mode was used to predict the unsteady temperature rising of the ball screws. Based on the performance of the two models abore, a new interval model was also built and the parameters of the new interval model were identified by the LS method. The results show that the error of temperature prediction is less than 0.5 ℃ for a single thermal source, and less than 0.8 ℃ for the double thermal sources.It concludes that the interval model built in the paper has good performance in prediction the temperature variations of ball screws.

参考文献

[1] 戴蓉, 谢铁邦. 新型一维位移工作台的设计及特性分析［J］. 光学精密工程，2006,14(3):428-433.

DAI R, XIE T B. Design and analysis of 1-DOF nano-positioning stage ［J］. Opt. Precision Eng., 2006,14(3):428-433. (in Chinese)

[2] 卢礼华, 郭永丰, 下河边明. 高增益 PID 控制器实现纳米定位［J］. 光学精密工程，2007,15(1):63-68.

LU L H, GUO Y F, TACHIKAWA, et al.. High-gain PID controller for nanometer positioning ［J］. Opt. Precision Eng., 2007,15(1):63-68. (in Chinese)

[3] 向红标, 裘祖荣, 李醒飞, 等. 精密实验平台的非线性摩擦建模与补偿［J］. 光学精密工程，2010,18 (5):1119-1127.

XIANG H B, QIU Z R, LI X F, et al.. Nonlinear friction modeling and compensation of high-precision experimental platforms ［J］. Opt. Precision Eng., 2010,18(5):1119-1127. (in Chinese)

[4] Huang Shyh Chour. Analysis of a model to forecast thermal deformation of ball screw feed drive systems ［J］. Int. J. Math. Tools Manufact., 1995,35(8):6.

[5] KIM S K,CHO D W. Real-time estimation of temperature distribution in a ball-screw system［J］. Int. J. Math. Tools Manufaet,1997,37(4):14.

[6] HOREJS O. Thermo-mechanical model of ball screw with non-steady heat sources. ［C］. 2007:133-137.

[7] AHN J, CHUNG S. Real-time estimation of the temperature distribution and expansion of a ball screw system using an observer ［C］. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2004,218(12):1667-1681.

[8] 夏军勇, 吴波, 胡友民, 等. 多变化热源下的滚珠丝杠热动态特性［J］. 中国机械工程，2008,19(8):955-958.

XIA J Y, WU B, HU Y M, et al.. The Thermal Dynamic Characteristic of Ball-screw under the variational multi-thermal Source ［J］. Chinese Mechanical Engineering,2008,19(18):955-958. (in Chinese)

[9] 严宗达, 王洪礼. 热应力［M］. 北京：高等教育出版杜,1993.

YAN Z D, WANG H L. Thermal Stress ［M］.Beijing:Higher Education Press, 1993.(in Chinese)

[10] 俞昌铭. 热传导及其数值分析［M］. 北京：清华大学出版社, 1981.

YU CH M. Thermal Conduction and its Numerical Analysis ［M］. Beijing:Tsinghua University Press, 1981.(in Chinese)

[11] 程光仁, 施祖康, 张超鹏. 滚珠螺旋传动设计基础［M］. 北京：机械工业出版社,1987.

CHENG G R, SHI Z K, ZHANG CH P. The Design of Ball Helical Transmission ［M］. Beijing:China Machine Press, 1987.(in Chinese)

陈诚, 裘祖荣, 李醒飞, 董成军, 张晨阳. 伺服系统中滚珠丝杠的温度场模型[J]. 光学精密工程, 2011, 19(5): 1151. CHEN Cheng, QIU Zu-rong, LI Xing-fei, DONG Cheng-jun, ZHANG Chen-yang. Temperature field model of ball screws used in servo systems[J]. Optics and Precision Engineering, 2011, 19(5): 1151.

伺服系统中滚珠丝杠的温度场模型

关于本站 Cookie 的使用提示

全站搜索

伺服系统中滚珠丝杠的温度场模型

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索