光学非球面三坐标测量中的像散补偿

利用三坐标测量仪在光学非球面镜研磨与粗抛阶段进行面形检测时, 测量结果常由于补偿程序不完善而出现像散误差。本文分析了非球面三坐标测量得到的数据, 指出测量结果中出现像散误差是测头半径补偿不准确所致。然后, 提出了一种离线数据处理方法对测量数据进行补偿来消除像散误差。该方法通过计算网格排列的测头中心点行和列方向的切向量得出曲面上每个点的法向矢量; 根据测头半径计算出测头球心到接触点的偏移量, 从而实现三坐标测量仪的三维测头半径补偿。球面样板实验显示这种方法可以将该样板测量中的像散峰谷值(PV)由4.921 9 μm减小到0.065 2 μm, 基本消除了测量结果中的像散误差, 提高了三坐标测量结果的准确度。实验结果验证了提出的三维测头半径补偿程序的有效性。

Abstract

When a three Coordinate Measurement Machine is used to test the surface shape of an aspheric element in grinding and polishing, obtained result often shows astigmatism errors due to an imperfect compensation programming. This paper analyzes these measurement data, and points out that the astigmatism errors comes from the imprecise compensation programming for the radius of three-dimensional probe in the CMM. Then, It presents an off-line data processing method to compensate the measurement data and to eliminate the astigmatism. By calculation of the tangent vectors of row and column at the meshed central point, the normal vector of each point on the surface is obtained. By calculation of the offsets between the centers of probe and the contact points, the radius of the tree-dimensional probe in the CMM is compensated. The experiment of a standard sphere show that this method decreases the astigmatism PV(Peak-to-Valley) of the measurement result from 4.921 9 μm to 0.065 2 μm, eliminating basically the astigmatism errors and improving the accuracy of the coordinate measurement. Obtained results verify the effectiveness of the proposed compensation programming for the radius of tree-dimensional probe in the CMM.

参考文献

[1] 王建明.三坐标轮廓测量仪检测非球面研究［D］.苏州: 苏州大学,2013.

WANG J M. Study on aspheric surface measurement using coordinate contour measuring machine ［D］. Suzhou:Soochow University, 2013. (in Chinese)

[2] 李圣怡.大中型光学非球面镜制造与测量新技术［M］.北京: 国防工业出版社,2011.

LI SH Y. New Technology for Manufacturing and Measurement of Large and Middle-Scale Aspheric Surfaces ［M］. Beijing:Changsha:National Defend Industry Press ,2011. (in Chinese)

[3] 蔺小军,王增强,单晨伟.自由曲面CMM测量测头半径补偿方法［J］.航空制造技术,2011(10):68-70,78.

LIN X J,WANG Z Q,SAN CH W. Method of probe radius compensation for free surface measurement by CMM ［J］. Aeronautical Manufacturing Techonglogy,2011(10):68-70,78. (in Chinese)

[4] 全荣,翁玲.三坐标测量机测头半径对测量数据的影响及其消除方法［J］.计量学报,1993(4):251-255.

QUAN R,WENG L.The influence of probe radius on the test data in three-coordinate measuring machine and its eliminating method ［J］. Acta Metrologica Sinica ,1993(4):251-255. (in Chinese)

[5] LIANG S R, LIN A C. Probe-radius compensation for 3D data points in reverse engineering ［J］. Computers in Industry, 2002, 48(3):241-251.

[6] MAYER J R R, MIR Y A, TROCHU F, et al.. Touch probe radius compensation for coordinate measurement using kriging interpolation ［J］. Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture, 1997, 211(1):11-18.

[7] LIN Y C, SUN W I. Probe radius compensated by the multi-cross product method in freeform surface measurement with touch trigger probe CMM ［J］. The International Journal of Advanced Manufacturing Technology, 2003, 21(10):902-909.

[8] 郭隐彪,郭江,王振忠.非球面检测路径与高精度曲线拟合算法研究［J］.中国机械工程, 2008, 19(10):1201-1204.

GUO Y B,GUO J,WANG ZH ZH. Study on measuring path and high-precision curve fitting algorithm for axisymmetric aspheric optics ［J］. China Mechanical Engineering, 2008, 19(10):1201-1204. (in Chinese)

[9] 王红敏.三坐标测量机测头半径补偿技术及应用［J］.制造技术与机床, 2010(6):109-112,115.

WANG H M. Compensation technology and application for probe radius of coordinate measuring machine ［J］. Technology and Test,2010(6):109-112,115. (in Chinese)

[10] 贾立德,郑子文,李圣怡,等.光学非球面坐标测量中位姿误差的分离与优化［J］.光学精密工程,2007, 15(8):1229-1234.

JIA L D,ZHENG Z W,LI SH Y, et al.. Separation and optimization of posture errors in optical aspheric coordinate measurement ［J］. Opt. Precision Eng.,2007, 15(8):1229-1234. (in Chinese)

[11] 颉赤鹰,陈少克.三坐标测量机测头半径补偿的新方法［J］. 组合机床与自动化加工技术, 2006(1):50-52.

XIE CH Y,CHEN SH K. A new method of the CMM probe radius compensation ［J］. Modular Machine Tool & Automatic Manufacturing Technique,2006(1):50-52.(in Chinese)

[12] 尤越,王乔方,字正华.一种基于Matlab的非球面光学元件面形参数测试技术［J］.红外技术, 2014(4):331-335.

YOU Y,WANG Q F, ZI ZH H. A test technique of surface shape aspheric optics parameters based on matlab ［J］. Infrared Technology, 2014(4):331-335.(in Chinese)

范晓明, 罗词金, 徐学科, 吴令奇, 胡晨. 光学非球面三坐标测量中的像散补偿[J]. 光学精密工程, 2016, 24(12): 3012. FAN Xiao-ming, LUO Ci-jin, XU Xue-ke, WU Ling-qi, HU Chen. Compensation of astigmatism in coordinate measurement for optical aspheric elements[J]. Optics and Precision Engineering, 2016, 24(12): 3012.

光学非球面三坐标测量中的像散补偿

关于本站 Cookie 的使用提示

全站搜索

光学非球面三坐标测量中的像散补偿

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索