工艺参数对Rene80激光定向凝固组影响研究

张冬云; 李志波; 赵恒; 左铁钏

doi:doi:10.3788/al20133302.113

应用激光, 2013, 33 (2): 113, 网络出版: 2013-05-22

工艺参数对Rene80激光定向凝固组影响研究

Research of the Influence of Processing Parameter on Laser Directional Solidification Structure

论文大纲

张冬云 ^*李志波赵恒左铁钏

作者单位

北京工业大学激光工程研究院, 北京 100124

激光金属外延成形定向凝固显微组织转向枝晶 epitaxial laser metal forming(E-LMF) directional solidification microstructure orientation changed dendrite

摘要

定向凝固组织由于显著减少了垂直于应力轴的横向晶界, 使合金具有优异的高温蠕变及持久性能, 因而在航空发动机涡轮叶片的制造中使用越来越广泛。采用激光金属外延成形(E-LMF)方法, 进行了工艺参数对Rene80镍基高温合金定向凝固组织影响的研究。研究内容包括工艺参数对成形件定向凝固组织类型、枝晶间距和转向枝晶区高度的影响规律以及基材晶体取向对定向凝固枝晶形貌的影响。结果表明, 枝晶一次间距随激光功率的增加而增大, 随扫描速度的增加而减小; 转向枝晶区高度随激光功率的提高而增大, 随扫描速度的提高而减小; 只有基材晶体取向与择优取向相近或一致才能得到外延定向连续生长的凝固组织。

Abstract

Directional solidification microstructure reduces significantly the amount of transverse grain boundary perpendicular to the main stress axis, what makes itself with excellent high temperature creep and lasting property and more and more applications in manufacturing of aeroengine turbine blade are found. The investigation under the effects of technological parameters on directional solidification microstructure for Rene80 by E-LMF was carried out. The research includes the influence rules of technological parameters on directional solidification structure style, primary dendrite arm spacing and the height of orientation changed dendrite area and the effect of substrate crystal orientation on dendrite morphology of directional solidification. The results show that primary dendrite arm spacing increases with the increase of laser power and decreases with scanning speed; the height of orientation changed dendrite area increases with the increase of laser power and decrease with the increase of canning speed; only when the substrate crystal orientation and preferred orientation is similar or consistent the solidification structure of continuous epitaxial directional growth could obtained.

参考文献

[1] GAUMANN M, RUSTERHOLZ H, KURZ W. Single Crystal Turbine Components Repaired by Epitaxial Laser Metal Forming: Materials for Advanced Power Engineering 1998, J. Lecomte-Beckers, et al [C]. Germany: Forschungszentrum J.lich, 1998: 1486-1497.

[2] GAUMANN M, HENRY S, CLETON F, et al. Epitaxial laser metal forming: analysis of microstructure formation [J]. Materials Science and Engineering, A, 1999(271): 232-241.

[3] YOSHIHIRO FUJITA, KAZUYOSHI SAIDA, KAZUTOSHI NISHIMOTO. Laser Epitaxial Cladding of Ni-base Single Crystal Superalloy [J]. Materials Science Forum Vols, 2008(580-582): 67-70.

[4] 张亚玮, 张述泉, 王华明. 激光熔化沉积定向快速凝固高温合金组织及性能[J]. 稀有金属材料与工程, 2008(37): 169-172.

[5] 金具涛, 张永忠, 石力开, 等. 激光熔化沉积Rene95镍基高温合金的凝固组织及力学性能[J]. 稀有金属, 2009(33): 805-809.

[6] 冯丽萍, 黄卫东, 林鑫, 等. FGH95合金激光成形定向凝固显微组织与性能[J]. 中国有色金属学报, 2003 (13) : 181-187.

[7] 《中国航空材料手册》编辑委员会. 中国航空材料手册[M]. 北京: 中国标准出版社, 2002: 771-772.

[8] 冶军. 美国镍基高温合金[M]. 北京: 科学出版社, 1978. 450-451.

[9] HUNT J D. In Solidification and Casting of Metals[M]. London: The Metal Society, 1979.

[10] 黄卫东. 激光立体成形[M]. 西安: 西北工业大学出版社, 2007: 126-135.

[11] 杨爱民. K4169高温合金组织细化及性能优化研究[D]. 西安: 西北工业大学, 2002

[12] WANG JIAJIN. Laser processing technologies[M]. Beijing: China Metric Process, 1992(9): 10-15..

[13] HUNT J D. Steady state columnar and equiaxed growth of dendrites and eutectic [J]. Mater. Sci. Eng., 1984(65): 75-83.

[14] 冯丽萍, 黄卫东, 李延民, 等. 基材晶体取向对激光多层涂覆微观组织的影响[J]. 中国激光, 2001, 28(10): 949-952.

[15] FENG LIPING, HUANG WEIDONG, LIN XIN, et al. Laser Multi-layer Cladding Experiment on the DD3 Single Crystal Using FGH95 Powder [J]. Chinese Journal of Aeronautics, 2002(2): 121-127.

张冬云, 李志波, 赵恒, 左铁钏. 工艺参数对Rene80激光定向凝固组影响研究[J]. 应用激光, 2013, 33(2): 113. Zhang Dongyun, Li Zhibo, Zhao Heng, Zuo Tiechuan. Research of the Influence of Processing Parameter on Laser Directional Solidification Structure[J]. APPLIED LASER, 2013, 33(2): 113.

工艺参数对Rene80激光定向凝固组影响研究

关于本站 Cookie 的使用提示

全站搜索

工艺参数对Rene80激光定向凝固组影响研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索