1 江苏大学 机械工程学院, 镇江 212013
2 中国科学院 南京天文仪器有限公司, 南京 210042
为了减少多个星敏感器地面热漂移标定时受到不同安装平台的位置误差影响,采取一种多星敏感器地面热漂移标定位置误差检测方法, 进行了理论分析和实验验证, 取得了-25℃~60℃真空状态下系统中基准方棱镜变形的位置偏移量数据, 并进行了标定位置误差精度分析。结果表明, 多星敏感器位置绕各轴产生的最大偏移量分别为-39.341″/℃,-0.060″/℃,-24.137″/℃, 通过建立误差检测模型对位置误差进行计算, 将其从姿态测量结果的偏移量中剔除后获得更准确的星敏感器姿态测量四元数, 剔除位置误差后的系统精度至少提高了11%。该研究在提高星敏感器热漂移标定精度方面具有很好的应用前景。
测量与计量, 标定位置误差, 四元数姿态解算, 星敏感器 measurement and metrology calibration position error quaternion solution attitude star sensor thermal drift
Author Affiliations
Abstract
1 School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, China
2 Nanjing Astronomical Instruments Co., Ltd., Chinese Academy of Sciences, Nanjing 210000, China
The photoelectric properties of conductive films are improved by doping Ag on aluminum-doped zinc oxide (AZO) films by laser induced forward transfer (LIFT). Firstly, the picosecond laser induced transfer mechanism of Ag films was revealed by numerical simulation; then, different-thickness Ag films were deposited on the AZO films by picosecond LIFT. When the film thickness is 30 nm and 50 nm, we have successfully obtained some Ag-AZO films with better optoelectronic properties by adjusting the laser parameters.
LIFT surface treatment AZO film Ag-nanoparticles optoelectronic property Chinese Optics Letters
2020, 18(4): 043101
1 中国科学院南京天文仪器研制中心, 江苏 南京 210042
2 中国科学技术大学, 安徽 合肥 230026
3 江苏大学, 江苏 镇江 212013
提出一种基于误差解耦的星敏感器热漂移标定系统。根据标定原理和星等模拟要求,设计自准直光学标定系统和误差解耦光路。根据共光路特性,由自准直仪和CCD获得星敏感器安装误差和热变形与安装变形形成的耦合误差,将安装变形误差从耦合误差中剔除后获得准确的星敏感器姿态转移四元数。仿真试验结果表明,温度范围在-25~60 ℃环境下,星敏感器标定时绕各轴产生的最大变化误差分别为0.2638,0.1317,0.0472 (″)/℃,与理想结果误差控制在0.02 (″)/℃的范围内,这为减少星敏感器标定中产生的耦合误差和提高热漂移标定精度提供一种新的思路和方法。
测量 星敏感器 误差解耦 标定 中国激光
2019, 46(10): 1004004