基于SH0导波的电磁超声换能器设计与实验研究

传统基于周期性永磁体的电磁超声换能器结构较复杂, 为此该文提出了一种由单一永磁体和导线阵列线圈构成的电磁超声换能器（EMAT）用于激发板中的SH0导波。首先叙述了设计的原理, 并采用有限元软件进行三维数值仿真分析, 利用水平极化永磁体垂直于板面的磁场在铝板中成功激发出SH0导波。为使EMAT换能效率达到最优, 研究长和宽为10 mm×25 mm的永磁体, 其高度及线圈匝数不同时EMAT激励的效率。仿真结果表明, 选用永磁体高度为25 mm及线圈匝数为37时EMAT换能效率和声场指向性较好。在此基础上, 通过实验研究了不同线圈匝数对换能器换能效率的影响, 实验结果与仿真结果一致, 充分验证了该文设计EMAT的方法具有可行性。

Abstract

The structure of the traditional electromagnetic ultrasonic transducer(EMAT) based on periodic permanent magnets is relatively complicated. In order to overcome this shortcoming, this paper presents an EMAT composed of a single permanent magnet and a wire array coil to excite the SH0 guided wave in the plate.First, the principle of the design is described,and the finite element software is used for three-dimensional numerical simulation analysis.The SH0 guided wave is successfully excited in an aluminum plate by using the magnetic field of the horizontally polarized permanent magnet perpendicular to the surface of the plate.In order to optimize the energy conversion efficiency of EMAT,the EMAT efficiency of the permanent magnet with the length and width of 10 mm×25 mm is investigated when the height and the coil turns are different. The simulation results demonstrate that the EMAT energy conversion efficiency and sound field pointing performance are better when the height of the permanent magnet is 25 mm and the number of coil turns is 37. On this basis, the effect of different coil turns on the transducer efficiency is studied through experiments. The experimental results are consistent with the simulation results, which fully verify the feasibility of the EMAT design method in this paper.

参考文献

[1] 张闯,魏琦,刘素贞,等.小尺寸试件检测用单向单模态电磁超声换能器设计［J］.电工技术学报,2019,34(17):3563-3571.

[2] RIBICHINI R,CEGLA F,NAGY P B,et al.Study and comparison of different EMAT configurations for SH wave inspection［J］.IEEE Transactions on Ultrasonics Ferroelectrics & Frequency Control,2011,58(12):2571-2581.

[3] JIAO J,Xi Z,He C, et al. Experiments on non-destructive testing of grounding grids using SH0 guided wave［J］. Insight: Non-Destructive Testing & Condition Monitoring, 2012, 54(7):375-379.

[4] 刘素贞,刘亚洲,张闯,等.SH导波在钢板缺陷检测中的传播特性［J］.声学技术,2017,36(2):140-146.

[5] 吕敬祥,刘国强.磁声电无损检测及改进的EMD消噪方法［J］.电工技术学报,2018,33(17):3935-3942.

[6] DHAYALAN R,BALASUBRAMANIAM K.A hybrid finite element model for simulation of electromagnetic acoustic transducer (EMAT) based plate waves［J］.Ndt & E International,2010,43(6):519-526.

[7] 翟国富,梁宝,贾文斌,等.横波电磁超声相控阵换能器设计［J］.电工技术学报,2019,34(7):1441-1448.

[8] 刘素贞,董硕,张闯,等.电磁超声加载方式对Lamb波模态的影响［J］.电工技术学报,2018,33(19):4426-4433.

[9] VASILE C F,THOMPSON R B.Excitation of horizontally polarized shear elastic waves by electromagnetic transducers with periodic permanent magnets［J］.Journal of Applied Physics,1979,50(4):2583-2588.

[10] HIRAMOTO T,OKAZAKI K,SUGIURA T.Study on EMAT configuration for generating SH waves［J］.AIP Conference Proceedings,2014,1581:444-449.

[11] 张志钢,阙沛文,雷华明.弹性层中的SH板波传播特性及电磁超声激励方法的研究［J］.传感技术学报,2005, 18(2):426-429.

[12] 焦敬品,刘文华,张永强,等.基于磁致伸缩效应的SH波电磁超声换能器设计［C］//北京: 2010振动与噪声测试峰会论文集, 2010:284-284.

[13] MA Q,JIAO J,HU P,et al.Excitation and detection of shear horizontal waves with electromagnetic acoustic transducers for nondestructive testing of plates［J］. Chinese Journal of Mechanical Engineering,2014, 27(2):428-436.

[14] 刘素贞,王淑娟,张闯,等.钢板电磁超声表面波的仿真分析及缺陷定量检测［J］.电工技术学报,2020,35(1):97-105.

[15] RIBICHINI R,CEGLA F,NAGY P B,et al.Experimental and numerical evaluation of electromagnetic acoustic transducer performance on steel materials［J］.Ndt & E International,2012,45(1):32-38.

[16] 刘素贞,张闯,金亮,等.电磁超声换能器的三维有限元分析［J］.电工技术学报,2013,28(8):7-12.

崔雅鑫, 张应红, 胡芷逸, 钱征华, 马智勇. 基于SH0导波的电磁超声换能器设计与实验研究[J]. 压电与声光, 2021, 43(4): 443. CUI Yaxin, ZHANG Yinghong, HU Zhiyi, QIAN Zhenghua, MA Zhiyong. Design and Experimental Investigation of Electromagnetic Acoustic Transducer Based on SH0 Guided Wave[J]. Piezoelectrics & Acoustooptics, 2021, 43(4): 443.

基于SH0导波的电磁超声换能器设计与实验研究

关于本站 Cookie 的使用提示

全站搜索

基于SH0导波的电磁超声换能器设计与实验研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索