7075铝合金中厚板激光扫描焊接气孔抑制机理研究

针对7075-T6铝合金10 mm中厚板开展了激光扫描焊试验和模拟研究，通过X射线无损检测以及熔池流动模拟，探究激光扫描焊接对焊缝气孔的抑制规律。试验结果表明，随着扫描频率和扫描振幅的增加，焊缝气孔率有降低趋势。分析不同扫描频率下的模拟结果发现，高频扫描下由于匙孔叠加会产生“大匙孔”结构，此结构相较低频扫描下的细长匙孔来说更加稳定，更不容易坍塌形成气泡；同时光束扫描增加了熔池宽度，增大了气泡逸出的概率。分析不同扫描振幅下的模拟结果发现，大振幅显著降低了匙孔的深度，从而降低了匙孔的深宽比，增强了匙孔的稳定性；同时增大振幅进一步扩大了熔池的宽度，增大了气泡逸出概率，进而降低了焊缝中的气孔率。

Abstract

Laser scanning welding experiment and simulation study were carried out for 7075-T6 aluminum alloy 10 mm medium thickness plate. The inhibition law of laser scanning welding on weld porosity was investigated by X-ray nondestructive testing and molten pool flow simulation. Experimental results show that the porosity decreases with the increase of scanning frequency and amplitude. By analyzing the simulation results at different scanning frequencies, it is found that the "large keyhole" structure is more stable and less likely to collapse and form bubbles due to the superposition of keyholes at high frequency scanning, compared with the slender keyhole at low frequency scanning. At the same time, the beam scanning increases the width of molten pool and the probability of bubbles escaping. By analyzing the simulation results under different scanning amplitudes, it is found that the large amplitude significantly reduces the depth of the keyhole, which reduces the aspect ratio of the keyhole and enhances the stability of the keyhole. At the same time, the increase of amplitude further expands the width of the molten pool, which increases the probability of bubble escape and then reduces the porosity in the weld.

参考文献

[1] 陈国庆, 柳峻鹏, 树西, 等. 铝合金焊接工艺的研究进展［J］. 焊接, 2017(9): 7-12.

[2] 唐思熠, 张学军, 郭绍庆, 等. 航空铝合金激光焊接的研究进展［J］. 电焊机, 2014, 44(6): 7-12.

[3] 吕国祥. 激光焊接工艺的现状与进展［J］. 科技风, 2014(15): 244.

[4] 陶武, 杨上陆. 铝合金激光焊接技术应用现状与发展趋势［J］. 金属加工(热加工), 2021(2): 1-4.

[5] 董彦妮, 张振鹏. 焊接技术在轨道交通车体中应用现状及发展趋势［J］. 科学技术创新, 2019(5): 173-174.

[6] 赵耀邦, 张小龙, 李中权, 等. 铝合金激光焊接技术研究进展［J］. 电焊机, 2017, 47(2): 8-12.

[7] 胡敏英, 吴志生. 铝合金激光焊接的工艺特点及发展现状［J］. 铝加工, 2007(4): 36-38.

[8] 宋新华, 金湘中, 陈胜迁, 等. 激光-电弧复合焊接及应用于车身制造的进展［J］. 激光技术, 2015, 39(2): 259-265.

[9] KATAYAMA S, NAITO Y, UCHIUMI S, et al. Physical phenomena and porosity prevention mechanism in laser-arc hybrid welding［J］. Transactions of JWRI, 2006, 35: 13-18.

[10] 巴一, 韩善果, 师文庆, 等. 激光摆动焊接的功率对钢/铝焊接接头的影响［J］. 激光技术, 2022, 46(2): 193-198.

[11] 刘怀亮, 周邵巍, 马修泉, 等. 激光摆动焊接6061铝合金板材焊缝成形工艺研究［J］. 机电工程技术, 2020, 49(2): 65-67.

[12] 殷彦杰. 旋转激光-电弧复合焊接铝合金气孔抑制作用研究［D］. 成都: 西南交通大学, 2019.

[13] 曹浩, 雷振, 黄瑞生, 等. 激光摆动焊接工艺参数对高强钢气孔率和焊缝成形的影响［J］. 焊接, 2019(4): 39-43.

[14] 宋友宝, 李龙, 吕金明, 等. 7xxx系铝合金焊接研究现状与展望［J］. 中国有色金属学报, 2018, 28(3): 492-501.

[15] 康悦, 占小红, 封小松, 等. 6061铝合金激光焊温度场与应力场数值模拟研究［J］. 上海航天(中英文), 2020, 37(6): 58-63.

[16] MAZUMDER J, STEEN W M. Heat transfer model for cw laser material processing［J］. Journal of Applied Physics, 1980, 51(2): 941-947.

[17] 周旭东, 吴友发, 陈帅, 等. 服役载荷下铝锂合金激光焊接T型接头残余应力的有限元分析［J］. 航空制造技术, 2020, 63(13): 75-82.

[18] 吴家洲. 激光深熔焊接过程流体流动分析和传热传质机理研究［D］. 南昌: 南昌大学, 2019.

[19] 潘井春. 钢/铝异种金属激光深熔焊过程中熔池行为及机理研究［D］. 长沙: 湖南大学, 2018.

[20] CHO W I. Numerical simulation of molten pool dynamics in high power disk laser welding［J］. Journal of Materials Processing Technology, 2012, 212(1): 262-275.

[21] KAWAGUCHI I, TSUKAMOTO S, ARAKANE G, et al. Formation mechanism of porosity in deep penetration laser welding-study on prevention of porosity in high power CO2 laser welding (report 2) ［J］, Quarterly Journal of The Japan Welding Society, 2006, 24: 338-343.

严建强, 陈永炜, 王志勇, 楼平, 李响, 殷志敏, 汤超, 王利民, 郝思远. 7075铝合金中厚板激光扫描焊接气孔抑制机理研究[J]. 应用激光, 2023, 43(1): 1. Yan Jianqiang, Chen Yongwei, Wang Zhiyong, Lou Ping, Li Xiang, Yin Zhimin, Tang Chao, Wang Limin, Hao Siyuan. Study on the Porosity Control Mechanism of Medium Thick 7075 Aluminum Alloy Plate by Scanning Laser Welding[J]. APPLIED LASER, 2023, 43(1): 1.

7075铝合金中厚板激光扫描焊接气孔抑制机理研究

关于本站 Cookie 的使用提示

全站搜索

7075铝合金中厚板激光扫描焊接气孔抑制机理研究

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索